Page 46 / 58 Scroll up to view Page 41 - 45
zNID 24xx Installation
46
zNID Hardware Installation Guide
Connect to network
Connecting the SC connectors
Connect the SC connector from the electronics module to the SC connector in
the zNID enclosure.
Observe the necessary precautions to decrease the risk of exposure to laser radiation.
WARNING!
Risk of eye damage. At all times when handling
optical fibers, follow the safety procedures recommended by your
company.
AVERTISSEMENT
! Risque de blessure aux yeux. Lors de la
manipulation de fibres optiques, suivez en permanence les
procédures de sécurité recommandées par votre société.
Although Zhone optical products have a Class I certification, hazardous
exposure to laser radiation can occur when fibers are connected, disconnected
or broken. Handling of optical fibers without dust caps increases the risk of
exposure. Exposure to either visible or invisible laser light can damage your
eyes under certain conditions.
1
Remove the
fiber service cover by removing the fiber service screw and
then sliding the fiber service cover forward (toward the connection panel
of the zNID).
Using your thumb push on the raised marking on the fiber service cover to
slide it off.
For a new unit the fiber service cover will be in a bag, so you will not
need to do this step.
Figure 13:
zNID-GPON-24xx model uses SC/APC connector (green)
Page 47 / 58
Connect to network
zNID Hardware Installation Guide
47
Figure 14:
zNID-GE-24xx model uses SC/UPC connector (blue)
2
Remove the dust covers from the SC optical connectors.
Clean the connector if necessary.
3
Plug in the fiber connector to connect the zNID to the network.
Note:
To function properly the optical strength to the zNID
should be between -8dBm and
-27dBm for GPON and between
-2dBm and
-23dBm for GE units. See
Testing optical power
on
page 44
for information.
4
Reattach the fiber service cover onto the zNID including the fiber service screw.
Page 48 / 58
zNID 24xx Installation
48
zNID Hardware Installation Guide
Connect power
The zNID is powered by AC power using the adapter which is shipped with
the unit. An optional uninterruptable power supply may also be used.
Figure 15:
The zNID 24xx has both AC input and UPS input for power
Note:
The AC input and UPS input must not be used at the same
time.
For pinout information for the UPS connector, see
UPS pinouts
on page 55
.
Page 49 / 58
Connect to network
zNID Hardware Installation Guide
49
Connecting phone terminals
The zNID 24xx models have the ability to connect POTS via RJ-11.
Connecting POTS
The zNID 24xx models have the ability to connect POTS via RJ-11 connector.
The terminal connections are shown in
Figure 16
.
1
Locate the subscriber’s telephone wire pair.
Figure 16:
Connect phone lines
2
If the wire pair is not terminated, follow local practices to attach an RJ-11
connector.
3
Plug the wire pair with RJ-11 connector into one of the zNID RJ-11 phone
jacks.
4
Repeat steps 1-3 as needed to connect additional phone lines.
For pinout information for the POTS connector, see
POTS pinouts
on page 54
.
Page 50 / 58
zNID 24xx Installation
50
zNID Hardware Installation Guide
Connecting Ethernet ports
The zNID-24xx series models have up to 4 Gigabit Ethernet ports.
Connect Ethernet ports
The zNID provides RJ eight pin modular jacks (RJ45) for Ethernet
connections. Ethernet connections can be used to deliver any packet services
including IPTV, data, and VoIP.
For Ethernet services, connect a Category 5 or a Category 6 cable to an RJ45
interface as shown in
Figure 17
.
1
Locate the Ethernet LAN cable.
2
If the cable is not terminated, follow local practices to attach an RJ-45
connector.
3
Plug the Ethernet cable into the appropriate RJ-45 Ethernet port.
Figure 17:
The RJ-45 Ethernet ports.
4
Repeat steps 1-3 as needed to connect additional Ethernet cables.
For pinout information for the Gigabit Ethernet connector, see
Gigabit
Ethernet pinouts
on page 53
.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top