Zhone 6519-A2-XXXX Router Manual PDF (Setup & Configuration Guide)

Page 16 / 145 Scroll up to view Page 11 - 15

65xx-A1 Family Router Users Guide

16

Back Panel

NOTE:

The below port descriptions are listed as they appear on the back panel from left to right.

Port

Description

DSL

RJ-11 cable connects to incoming DSL line

LAN1 – LAN4

RJ-45 connects the unit to an Ethernet device such as a PC or a

switch.

Reset / Default

Restart

—press the button for less than 4 seconds.

ISP settings

—press the button for 4 seconds or longer.

Factor y Default settings

– press the button for 60 seconds or

longer

Power

Connects to a 12V 700 mA power adapter.

Switch

Power on (depressed) or power off for the router.

NOTE:

The 6512 and 6511 do not have the wireless antenna. The 6511 has one LAN port.

Page 17 / 145

65xx-A1 Family Router Users Guide

17

Chapter 2

Hardware Installation and PC Setup

Overview

This chapter provides basic instructions for connecting the router to a computer or a LAN and to

the Internet using DSL. The first part provides instructions to set up the hardware, and the second

part describes how to prepare your PC for use with the router. Refer to Chapter 3, Using the Web

Interface for configuration instructions.

It is assumed that you have already subscribed to DSL service with your telephone company or

other Internet service provider (ISP).

Connecting Your Hardware

Shut down your PC before connecting the router. To connect your modem:

1.

Connect the ADSL Line

Connect one end of an RJ-11 cable from your ADSL connection and the other end to the

LINE port of the modem.

2.

Connect the PC to the Router

To use the Ethernet connection, connect the Ethernet cable from the computer directly to the

router. Connect one end of the Ethernet cable to one of the four ports labelled LAN on the

back of the router and attach the other end to the Ethernet port of your computer.

Page 18 / 145

65xx-A1 Family Router Users Guide

18

3.

Connect the Power Adapter

Complete the process by connecting the AC power adapter to the POWER connector on the

back of the device and plug the adapter into a wall outlet or power strip. Then turn on and

boot up your PC and any LAN devices, such as hubs or switches, and any computers

connected to them.

Mounting the Router

The router can be mounted on the wall with two screws. Mounting can be done on wall material

including concrete, wood, or drywall. Select an appropriate location free from obstructions or any

possible interference. Make sure the cables can be easily attached to the router without strain.

The illustration below shows how to mount the router horizontally on a wall.

NOTE

: Mount the router with the cables facing down, the LEDs facing up.

Page 19 / 145

65xx-A1 Family Router Users Guide

19

Unit dimensions

Model

Unit Dimensions

Mounting Holes

6511-A1

1.30" (H) x 7.25" (W) x 5" (D)

34.93 mm (H) x 184.15mm (W) x 127mm

(D)

2 holes- 5.375" (136.63mm)

apart

6512-A1

1.25"(H) x 8.25" (W) x 4.75" (D)

31.75 mm (H) x 209.55 mm (W) x 102.65

mm (D)

2 holes 6.125" (155.58mm)

apart

6518-A1

1.25" (H) x 8.25" (W) x 4.75" (D)

31.75 mm (H) x 209.55 mm (W) x 102.65

(D)

2 holes 6.125" (155.58mm)

apart

Page 20 / 145

65xx-A1 Family Router Users Guide

20

Model

Unit Dimensions

Mounting Holes

6519-X1

1.25" (H) x 8.25" (W) x 4.75" (D)

31.75 mm (H) x 209.55 mm (W) x 102.65

(D)

2 holes 6.125" (155.58mm)

apart

Configuring Your Computer

Prior to accessing the router through the LAN or the USB port, note the following necessary

configurations—

•

Your PC’s TCP/IP address:

192.168.1.__

( the last number is any number between 2 and

254)

•

The router’s default IP address:

192.168.1.1

•

Subnet mask: 255.255.255.0

Below are the procedures for configuring your computer. Follow the instructions for the operating

system that you are using.

If you used the Ethernet cable to connect your router and PC, you do not need any specific driver

installation.

Windows 2000

1.

In the Windows taskbar, click the Start button and point to

Settings

,

Control Panel

, and

Network and Dial-up Connections

(in that order).

2.

Click Local Area Connection. When you have the Local Area Connection Status window

open, click Properties.

3.

Listed in the window are the installed network components. If the list includes

Internet

Protocol (TCP/IP)

, then the protocol has already been enabled, and you can skip to Step

10.

4.

If Internet Protocol (TCP/IP) does not appear as an installed component, then click

Install

.

5.

In the

Select Network Component Type

window, click on protocol and then the

Add

button.

6.

Select

Internet Protocol (TCP/IP)

from the list and then click on

OK

.

7.

If prompted to restart your computer with the new settings, click

OK

.

8.

After your computer restarts, click the

Network and Dial-up Connections

icon again, and

right click on the

Local Area Connection

icon and then select

Properties

.

9.

In the

Local Area Connection Properties

dialog box, select

Internet Protocol (TCP/IP)

and then click

Properties

.

10.

In the

Internet Protocol (TCP/IP) Properties

dialog box, click the radio button labelled

Use

the following IP address

and type 192.168.1.x (where x is any number between 2 and 254)

and 255.255.255.0 in the IP address field and Subnet Mask field.

11.

Click

OK

twice to save your changes and then close the

Control Panel

.

Rate

Popular Zhone Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share