USRobotics USR5465 Router Manual PDF (Setup & Configuration Guide)

Page 6 / 20 Scroll up to view Page 1 - 5

2

Step Two: Connect your 802.11g 54Mbps Router to your computer and con-

nect the power supply

Connect one end of the supplied Ethernet cable to your

computer’s Ethernet adapter. Connect the other end to

one of the LAN ports on the 802.11g 54Mbps Router.

Turn on your cable or DSL modem. Connect the

included power adapter to the power socket on the

802.11g 54Mbps Router. Plug the power adapter into

a standard power outlet. Turn on your computer.

Step Three: Configure the basic connection settings

Perform the steps of the Setup Wizard to configure the basic connection settings of the 802.11g

54Mbps Router.

Note:

For more detailed configuration information, refer to the User Guide on the Installa-

tion CD-ROM.

Your Internet connection user name and password will be required for the installation of the

802.11g 54Mbps Router. Depending on your ISP, you may need to know some of the following

information: IP Address, Subnet Mask, Gateway/Router, DNS Servers/ Name Servers, and Ser-

vice Name (optional).

Note:

To obtain the necessary information, first look within your login application. If you

cannot find all the necessary information, contact your ISP for assistance in obtaining this

information.

Downloaded from

www.Manualslib.com

manuals search engine

Page 7 / 20

3

1.

Launch a Web browser. In the location or address line of your Web browser, type

http://192.168.2.1

to access the Web User Interface.

After the connection is established, you will see the Web User Interface.

The default pass-

word is

admin

.

Click

Login

.

When you access the Web User Interface, click the

Setup Wizard

.

Note:

If you are prompted to connect to the Internet, you may need to select

Try Again

or

Connect

, depending on your Internet browser.

2.

Select your Time Zone and then click

3.

Choose your Broadband Type. (Enter the appropriate information for the type of Internet

connection you chose.) When you are finished, click

4.

If required, enter the IP address Info for the 802.11g 54Mbps Router and then click

Finish

.

After finishing the Setup Wizard, if it does not report "Connected," perform the steps of the Setup

Wizard again.

If Web User Interface still did not report “Connected,” or if at anytime you want to validate your

Internet settings, click Advanced Setup and select Status.

To make a wireless connection:

Make sure each wireless adapter that will be con-

nected to the network is set to Infrastructure mode.

If you purchased the USR5470 Wireless Starter Kit,

refer to the Navigating the Wireless Configuration

Utility section of the 802.11g 54Mbps USB Adapter

User Guide on the Installation CD-ROM to deter-

mine how to change this setting and

for instruc-

tions on collecting your configuration information.

If you are connecting a different wireless adapter,

refer to that wireless adapter’s documentation.

When you are finished configuring the basic connection settings, you should now have Internet

access. Launch a Web browser and register your product at

www.usr.com/productreg

If the page

loads, you are finished with the installation procedure. If the page does not load, refer to the

Troubleshooting section.

Downloaded from

www.Manualslib.com

manuals search engine

Page 8 / 20

4

Note:

Refer to the “Configuring the 802.11g 54Mbps Router” section in the User Guide on

the Installation CD-ROM for more detailed configuration information. Contact your ISP if

you have any questions about your WAN type or your connection information.

The installation procedure for the 802.11g 54Mbps Router is now complete. Proceed to the Instal-

lation procedure for the 802.11g 54Mbps USB Adapter. If you experience any difficulties, refer to

the Troubleshooting section of this guide or to the User Guide on the Installation CD-ROM for

more detailed information.

Downloaded from

www.Manualslib.com

manuals search engine

Page 9 / 20

5

802.11g 54Mbps USB Adapter Installation

Prepare for Installation

ATTENTION:

You must install your software and drivers before you physically connect the 802.11g

54Mbps USB Adapter.

Note:

For the most updated information, visit:

http://www.usr.com/support

Turn on your desktop or laptop computer. Type your password if you are prompted to do so.

Note:

Be sure to find out what letter your CD-ROM drive uses before you begin installing

your new product. You will need to know this to properly install your software.

Note:

During the Installation procedure, you may be prompted for your Windows Operat-

ing system CD-ROM. Make sure you have it available in case you need it.

Note:

If the 802.11g 54Mbps USB Adapter does not fit into an available USB port on your

computer because of other USB devices that are connected, use an USB extension cable

or a USB hub to connect the 802.11g 54Mbps USB Adapter.

Note:

If you are connecting the 802.11g 54Mbps USB Adapter to a 1.1 USB port, you may

see a message informing you that a Hi-Speed USB device is being connected to a USB

port that is not Hi-Speed. This will not affect the installation procedure.

Step One: Install your software and drivers

Insert your U.S. Robotics Installation CD-ROM into your CD-ROM drive.

Note:

If your CD-ROM does not automatically launch, click Windows

Start

,

Run

, and type

D:\setup

(if your CD-ROM drive uses a different letter, type that letter in place of "D") and

click

OK

.

The Installation CD Graphic User Interface (GUI) will appear on your screen. If prompted, select

Model Number

Serial Number

USR5422

Downloaded from

www.Manualslib.com

manuals search engine

Page 10 / 20

6

your preferred language. Read the license agreement and click

Yes

.

Select the 802.11g 54Mbps USB Adapter and then click

Software

. Click

Wireless USB Adapter

Utility and Drivers

. Follow the on-screen instructions to finish the installation procedure.

If you are prompted, restart your computer and continue to follow the on-screen instructions.

Step Two: Install the 802.11g 54Mbps USB Adapter to your

computer.

When you are prompted, insert the 802.11g 54Mbps USB

Adapter into an available USB port on your computer.

Note:

Make sure the 802.11g 54Mbps USB Adapter is

fully inserted into the USB port on your computer so that the 802.11g 54Mbps USB

Adapter is detected.

Select your country. Windows will detect the new hardware. If prompted for the location of the

drivers, select

Install the software automatically (Recommended)

and click

Follow the on-screen instructions to complete the installation procedure.* If you are prompted,

restart your computer.

Downloaded from

www.Manualslib.com

manuals search engine

Rate

Popular USRobotics Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share