Page 56 / 119 Scroll up to view Page 51 - 55
Ubee Interactive
Using the Port Triggers Option
Ubee DVW326 Advanced Wireless Voice Gateway Subscriber User Guide
March 2014
52
4. Enter information in the Port Trigger fields as shown below. Field descriptions follow
the screen shot.
Label
Description
Trigger Start Port
Defines a port number or the starting port number in a range
of trigger port numbers.
Trigger End Port
Defines a port number or the ending port number in a range of
trigger port numbers.
Target Start Port
Defines a port number or the starting port number in a range
of target port numbers.
Target End Port
Defines a port number or the ending port number in a range of
target port numbers.
Protocol
Defines the protocol type for this rule, UDP, TCP, or Both.
Page 57 / 119
Ubee Interactive
Using the Port Triggers Option
Ubee DVW326 Advanced Wireless Voice Gateway Subscriber User Guide
March 2014
53
5. Click
Apply
. The port trigger rule is created and displayed in the table. Additional field
descriptions are listed below the screen example.
The following example shows the Port Triggering option set up for a dual Xbox
configuration.
Description
Names the triggering rule.
Enabled
Enables (on) or disables (off) the triggering rule.
Apply
Saves changes.
Remove All
Removes all of the input host’s MAC addresses.
Label
Description
Remove All
Deletes all the port trigger rules.
Edit
Allows you to edit the properties of the selected rule.
Remove
Deletes the selected rule.
Label
Description
Page 58 / 119
Ubee Interactive
Using the Pass Through Option
Ubee DVW326 Advanced Wireless Voice Gateway Subscriber User Guide
March 2014
54
6.7
Using the Pass Through Option
Use the
Pass Through
option to configure a pass through table. Devices in the pass
through table are treated as bridge devices, storing and forwarding data between LAN
interconnections.
Steps
To configure a pass through table:
1.
Click
Advanced
from the main menu.
2. Click
Pass Through
from the left side menu. The pass through fields are explained
following this screen example.
Page 59 / 119
Ubee Interactive
Using the DMZ Host Option
Ubee DVW326 Advanced Wireless Voice Gateway Subscriber User Guide
March 2014
55
6.8
Using the DMZ Host Option
Use the
DMZ
(Demilitarized Zone)
Host
option to expose a host IP address to the WAN
(public Internet). You can use this option when applications do not work with port triggers
or other networking strategies.
Steps
To set up a DMZ host:
1.
Connect a PC to an Ethernet port on the DVW326. Make sure both devices are
powered on and functioning.
2. Connect a Home Gateway (or other device you wish to be in the DMZ) to an Ethernet
port on the DVW326.
3. Log in to the DVW326 Web user interface.
4. Click
Advanced
from the main menu.
5. Click
DMZ Host
from the left side menu.
6. Enter the IP address of the Home Gateway (host device) to be exposed to the WAN.
7. Test the device to ensure Internet access is available and the device is functional. For
example, connect to the Internet from a PC connected to the Home Gateway, or make
calls from a VoIP phone.
Label
Description
Pass Through MAC Addresses
Allows you to enter the input host’s MAC address.
Add MAC Address
Adds the entered MAC address.
Addresses entered: n/32
Displays the MAC addresses to be blocked. The number of
MAC addresses is shown as 0/32 where 0 is the number of
addresses in the list. You can add up to 32 MAC addresses at
one time.
Remove MAC Address
Removes the selected input host’s MAC address.
Clear All
Removes all of the input host’s MAC addresses.
Page 60 / 119
Ubee Interactive
Using the DMZ Host Option
Ubee DVW326 Advanced Wireless Voice Gateway Subscriber User Guide
March 2014
56
Label
Description
DMZ Address
Defines the IP address of the host to be exposed.
Apply
Saves changes.

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top