1. Home
    2. /
  2. Manuals
    3. /
  3. Ubee
    4. /
  4. DVW3201B
    5. /
  5. 3
Page 11 / 96 Scroll up to view Page 6 - 10
Ubee Interactive
Understanding Specifications, Standards, and Firmware
Ubee DVW3201B Advanced Wireless Voice Gateway Subscriber User Guide
•
July 2012
7
Max Bandwidth of 4 Channels = 122.88 (108) Mbps, bandwidth per channel (up to
4 channels) = [QPSK 0.32 ~ 10.24 Mbps, 8 QAM 0.48 ~ 15.36 Mbps, 16 QAM 0.64
~ 20.48 Mbps, 32 QAM 0.80 ~ 25.60 Mbps, 64 QAM 0.96 ~ 30.72 Mbps, 128
QAM/TCM 30.72 Mbps]
Symbol Rate: 160, 320, 640, 1280, 2560, 5120 Ksps
RF Output Power: TDMA/ATDMA: +8dBmV to +54dBmV (32/64 QAM). ATDMA
Only: +8dBmV to +55dBmV (8/16 QAM), +8dBmV to +58dBmV (QPSK). S-CDMA:
+8dBmV to +53dBmV (all modulations)
*Actual speeds vary based on factors including network configuration and speed.
Security and Network
Supports 4 SSIDs, 802.11b/g/n compliant with link speeds up to 300 Mbps, 2Tx
and 2Rx antennas
NAT Firewall, MAC/IP/Port Filtering, Parental Control, Stateful Packet Inspection
(SPI), DoS Attack Protection, WPS/ WPA/ WPA2/ WPA-PSK & 64/128-bit WEP
Encryption
DHCP Client/Server, Static IP network assignment, RIPv1/ v2, Ethernet
10/100/1000 BaseT, full-duplex auto-negotiate functionality, IPv4 and IPv6 support
VPN Pass-Through and VPN End-Point Support (IPSec/L2TP/PPTP), TACACS or
RADIUS Authentication
Voice
MGCP 1.0 / NCS 1.0 and SIP (RFC3261)
Ring Voltage: 270 VAC, pk-pk (tip-ring), Line Voltage Onhook: -48 Volts, Loop
Current: 20mA / 41mA, Ring Capability: 2K ft., 5REN, Hook State: Signaling Loop
Start
DTMF Tone Detection, T.38 FAX Relay (G.711), Echo Cancellation (G.168) /
Silence Suppression, Voice Active Detection and Comfort Noise Generation
Device Management
Supports IEEE 802.11e Wi-Fi Multimedia (WMM) and UAPSD (power savings)
DOCSIS, Web-Based, and XML Configuration
Telnet Remote Management
Firmware Upgrade via TFTP
Configuration Backup and Restore
SNMP Support
Physical and Environmental
Dimensions: 9” (230mm) x 8.9” (228mm) x 2.36” (60mm)
Power: 10A / 125V
Humidity: 5~90% (non-condensing)
Operating Temperature: 32°F ~ 104°F (0°C ~ 40°C)
Page 12 / 96
Understanding Default Values and Logins
Ubee Interactive
8
Ubee DVW3201B Advanced Wireless Voice Gateway Subscriber User Guide
•
July 2012
1.7
Understanding Default Values and Logins
The DVW3201B is pre-configured with the following parameters. Some regions may
change default values using the cable modem or XML configuration file. Check with your
provisioning team to determine the default values for your region.
Local Port Address
Operation Mode
: NAT Mode
Subnet Mask
: 255.255.255.0
Wireless Defaults:
Primary SSID (subscriber-managed) = DVW3201B plus last 2 characters of the
cable modem’s MAC address with upper letters entered in upper case.
Example:
DVW3201BE3
Note:
If the subscriber changes the SSID, the device does not revert to this default
SSID when the device is reset, except when a manual reset is performed
through the Web UI (see
Understanding the Tools Menu on page 81
).
The MAC address can be found on the device label or it can be found by
opening an Internet browser window to the device. Refer to
Using the
Information Option on page 21
for instructions.
Encryption Method =
WPA2-PSK
with
AES
encryption
WPA Pre-shared Key = DVW3201B plus the last 6 characters (3 octets) of the
cable modem’s MAC address (UPPER case, if letters).
Example:
DVW3201B9822E3
WPS PIN = Randomly generated eight digit number
Device Name:
UbeeAP
Standard User Web Interface Login
:
Username:
user
Password:
user
1.8
Understanding LED Operations
The following section describes what the device LEDs indicate.
1.8.1
Understanding the Device Front Panel
The following image represents the front panel of the device. LED descriptions are
provided in the following table.
Page 13 / 96
Ubee Interactive
Understanding LED Operations
Ubee DVW3201B Advanced Wireless Voice Gateway Subscriber User Guide
•
July 2012
9
1.8.2
Understanding LED Behavior
The following table summarizes the behavior of the device LEDs.
LED
Color
Description
POWER
White
On
– Internal power-on completes successfully.
Blinks
– Power-on fails.
DS/US
White
Blinks
– Initializing.
On
– Locked on to upstream (US) and downstream (DS) channels and registered OK.
Blinks
– Unable to register or lock.
Blinks
– When a firmware upgrade is in progress, the DS/US and TEL1 LEDs blink, first one
then the other for a few seconds. Then DS/US and TEL1 and TEL2 LEDs blink in unison.
ONLINE
White
Blinks
– Obtaining an IP address and configuration file.
On
– Configuration completes successfully.
WiFi
White
On
– Wi-Fi is enabled.
Off
– Wi-Fi is disabled.
TEL1
TEL2
White
On
– Telephone is on-hook.
Blinks
– Telephone is off-hook.
Blinks
– When a firmware upgrade is in progress, the DS/US and TEL1 LEDs blink, first one
then the other for a few seconds. Then DS/US and TEL1 and TEL2 LEDs blink in unison.
Page 14 / 96
Understanding LED Operations
Ubee Interactive
10
Ubee DVW3201B Advanced Wireless Voice Gateway Subscriber User Guide
•
July 2012
BATTERY
White
On
– The battery is installed and AC power is on and properly functioning.
Off
– If there is no AC power to the device, the Battery LED is Off, the Power LED flashes,
and the TEL1 LED is On. All other LEDs are Off.
Blinks
– If the battery is at low power level (30mins left).
Ethernet 1-4
(back panel)
Orange
/
Green
On ORANGE
– When an Ethernet device is connected to the cable modem at 10/100 Mbps
speeds,
On GREEN
– When an Ethernet device is connected to the cable modem at 1000 speeds
(Gigabit Ethernet).
Blinks (in
ORANGE
or
GREEN
)
– When data is passed between the cable modem and the
connected device.
The Ethernet ports are used to connect Ethernet devices, such as computers, gaming
consoles, and/or routers/hubs to the DVW3201B using RJ45 cables. Each Ethernet port on
the back panel of the device has an LED to indicate its status when an Ethernet device is
connected.
WPS button
(top of
device)
White
Located on top of the cable modem, this button is used for the WiFi Protected Setup (WPS)
method to connect a PIN-protected WiFi device to the cable modem.
When a user pushes the WPS button or triggers WPS via the device’s Web UI, an LED on
the top-front of the device
blinks
for 4 minutes until a PIN is entered from the wireless client
that wishes to connect (for example, a laptop computer). After a WiFi client attaches
successfully, the LED remains
On
for 5 minutes, then turns
Off
. Refer to
Understanding the
Wireless Menu on page 57
for more information.
LED
Color
Description
LED POSITION
LED1
LED2
LED3
LED4
LED
DESIGNATION/LABEL
POWER
US/DS
ONLINE
WiFi
1
MTA DHCP
ON
ON
ON
2
MTA SNMP/TFTP
ON
ON
ON
3
RSIP
ON
ON
ON
On-Hook
Off-Hook
ON
ON
ON =
NETWORK
AVAILABLE
OFF =
NETWORK
NOT
AVAILABLE
STEP
eMTA INITIALIZATION
ON
eMTA NORMAL
OPERATION
AC POWER
NORMAL (AC
POWER IS ON)
Page 15 / 96
Ubee DVW3201B Advanced Wireless Voice Gateway Subscriber User Guide
•
July 2012
11
2
Installing the DVW3201B
This chapter explains how to set up and connect the DVW3201B, connect additional
devices, and troubleshoot the installation.
Topics
See the following topics:
Setting Up and Connecting the DVW3201B on page 11
Connecting Devices to the Network on page 12
Troubleshooting the Installation on page 14
2.1
Setting Up and Connecting the DVW3201B
Use the following instructions to set up and connect the DVW3201B. When the device is
set up and connected, refer to
Accessing the Web Interface on page 17
to configure the
device.
Important
: Subscribers contact your service provider to enable Internet access, wireless
networking, and telephony (voice). In particular, voice service requires additional steps for
the service provider including cancelling the previous telephone provider service, porting
the telephone number, and other tasks to minimize downtime during the transition.
Typically, the service provider initially configures and connects the device. The installation
steps are provided below if you wish to confirm the setup, or add devices to your network.
Refer to
Connecting Devices to the Network on page 12
.
Steps
To set up the device:
1.
Remove the contents from the device packaging.
2. Place the DVW3201B in the best location to connect to other devices, such as PCs or
gaming consoles.
Place the wireless cable modem and wireless clients in open areas far away from
transformers, heavy-duty motors, microwave ovens, refrigerators, fluorescent
lights, and other manufacturing equipment. These items can impact wireless
signals. A wireless signal can become weaker after it has passed through metal,
concrete, brick, walls, or floors.
Place the device in a location that has an operating temperature of 0
˚
C to
40
˚
C (32
˚
F to 104
˚
F). Refer to
Understanding Safety and Regulatory Information
on page 2
for more safety information.

Rate

3.7 / 5 based on 3 votes.

Popular Ubee Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top