1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TL-WR941ND
    5. /
  5. 14
Page 66 / 113 Scroll up to view Page 61 - 65
TL-WR941ND
Wireless N Router
¾
ALG -
It is recommended to enable Application Layer Gateway (ALG) because ALG allows
customized Network Address Translation (NAT) traversal filters to be plugged into the
gateway to support address and port translation for certain application layer "control/data"
protocols such as FTP, TFTP, H323 etc.
z
FTP ALG -
To allow FTP clients and servers to transfer data across NAT, keep the
default
Enable.
z
TFTP ALG -
To allow TFTP clients and servers to transfer data across NAT, keep the
default
Enable.
z
H323 ALG -
To allow Microsoft NetMeeting clients to communicate across NAT, keep
the default
Enable
.
Click the
Save
button to save your settings.
4.9.2 Advanced Security
Choose menu “
Security
→
Advanced Security
”, you can protect the Router from being
attacked by TCP-SYN Flood, UDP Flood and ICMP-Flood in the screen as shown in
Figure 4-38
.
Figure 4-38
Advanced Security
¾
Packets Statistics Interval (5~60) -
The default value is 10. Select a value between 5 and
60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time
section of the packets statistics. The result of the statistics is used for analysis by SYN Flood,
-57-
Page 67 / 113
TL-WR941ND
Wireless N Router
UDP Flood and ICMP-Flood.
¾
DoS Protection -
Denial of Service protection. Check the Enable or Disable button to
enable or disable the DoS protection function. Only when it is enabled, will the flood filters be
enabled.
)
Note:
Dos Protection will take effect only when the
Traffic Statistics
in “
System Tool
→
Traffic
Statistics
” is enabled.
¾
Enable ICMP-FLOOD Attack Filtering
-
Enable or Disable the ICMP-FLOOD Attack
Filtering.
¾
ICMP-FLOOD Packets Threshold (5~3600)
-
The default value is 50. Enter a value
between 5
~
3600. When the current ICMP-FLOOD Packets number is beyond the set value,
the Router will startup the blocking function immediately.
¾
Enable UDP-FLOOD Filtering
-
Enable or Disable the UDP-FLOOD Filtering.
¾
UDP-FLOOD Packets Threshold (5~3600)
-
The default value is 500. Enter a value
between 5
~
3600. When the current UPD-FLOOD Packets number is beyond the set value,
the Router will startup the blocking function immediately.
¾
Enable TCP-SYN-FLOOD Attack Filtering
-
Enable or Disable the TCP-SYN-FLOOD
Attack Filtering.
¾
TCP-SYN-FLOOD Packets Threshold (5~3600)
-
The default value is 50. Enter a value
between 5
~
3600. When the current TCP-SYN-FLOOD Packets numbers is beyond the set
value, the Router will startup the blocking function immediately.
¾
Ignore Ping Packet From WAN Port
-
Enable or Disable Ignore Ping Packet From WAN
Port. The default setting is disabled. If enabled, the ping packet from the Internet cannot
access the Router.
¾
Forbid Ping Packet From LAN Port
-
Enable or Disable Forbid Ping Packet From LAN Port.
The default setting is disabled. If enabled, the ping packet from LAN cannot access the
Router. This function can be used to defend against some viruses.
Click the
Save
button to save the settings.
Click the
Blocked DoS Host List
button to display the DoS host table by blocking.
4.9.3 Local Management
Choose menu “
Security
→
Local Management
”, you can configure the management rule in the
screen as shown in Figure 4-39. The management feature allows you to deny computers in LAN
from accessing the Router.
-58-
Page 68 / 113
TL-WR941ND
Wireless N Router
Figure 4-39 Local Management
By default, the radio button “
All the PCs on the LAN are allowed to access the Router's
Web-Based Utility
” is checked. If you want to allow PCs with specific MAC Addresses to access
the Setup page of the Router's Web-Based Utility locally from inside the network, check the radio
button “
Only the PCs listed can browse the built-in web pages to perform Administrator
tasks
”, and then enter each MAC Address in a separate field. The format for the MAC Address is
XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). Only the PCs with MAC address listed can
use the password to browse the built-in web pages to perform Administrator tasks while all the
others will be blocked.
After click the
Add
button, your PC's MAC Address will be placed in the list above.
Click the
Save
button to save your settings.
)
Note:
If your PC is blocked but you want to access the Router again, use a pin to press and hold the
Reset Button
(hole) on the back panel for about 5 seconds to reset the Router’s factory defaults
on the Router’s Web-Based Utility.
4.9.4 Remote Management
Choose menu “
Security
→
Remote Management
”, you can configure the Remote Management
function in the screen as shown in Figure 4-40. This feature allows you to manage your Router
from a remote location via the Internet.
-59-
Page 69 / 113
TL-WR941ND
Wireless N Router
Figure 4-40 Remote Management
¾
Web Management Port -
Web browser access normally uses the standard HTTP service
port 80. This Router's default remote management web port number is 80. For greater
security, you can change the remote management web port to a custom port by entering that
number in the box provided. Choose a number between 1 and 65534 but do not use the
number of any common service port.
¾
Remote Management IP Address
-
This is the current address you will use when accessing
your Router from the Internet. This function is disabled when the IP address is set to the
default value of 0.0.0.0. To enable this function change 0.0.0.0 to a valid IP address. If set to
255.255.255.255, then all the hosts can access the Router from internet.
)
Note:
1.
To access the Router, you should type your Router's WAN IP address into your browser's
address (in IE) or Location (in Navigator) box, followed by a colon and the custom port
number. For example, if your Router's WAN address is 202.96.12.8, and the port number
used is 8080, please enter http://202.96.12.8:8080 in your browser. Later, you may be
asked for the Router's password. After successfully entering the username and password,
you will be able to access the Router's web-based utility.
2.
Be sure to change the Router's default password to a very secure password
.
4.10 Parental Control
Choose menu “
Parental Control
”, and you can configure the parental control in the screen as
shown in Figure 4-41. The Parental Control function can be used to control the internet activities
of the child, limit the child to access certain websites and restrict the time of surfing.
-60-
Page 70 / 113
TL-WR941ND
Wireless N Router
Figure 4-41
Parental Control Settings
¾
Parental Control -
Check
Enable
if you want this function to take effect, otherwise check
Disable
.
¾
MAC Address of Parental PC -
In this field, enter the MAC address of the controlling PC, or
you can make use of the
Copy To Above
button below.
¾
MAC Address of Your PC -
This field displays the MAC address of the PC that is managing
this Router. If the MAC Address of your adapter is registered, you can click the Copy To
Above button to fill this address to the MAC Address of Parental PC field above.
¾
Website Description -
Description of the allowed website for the PC controlled.
¾
Schedule
-
The time period allowed for the PC controlled to access the Internet. For detailed
information, please go to “
Access Control
→
Schedule
”.
¾
Modify
-
Here you can edit or delete an existing entry.
To add a new entry, please follow the steps below.
1.
Click the
Add New…
button and the next screen will pop-up as shown in Figure 4-42.
2.
Enter the MAC address of the PC (e.g. 00-11-22-33-44-AA) you’d like to control in the MAC
Address of Child PC field. Or you can choose the MAC address from the All Address in
Current LAN
drop-down list.
3.
Give a description (e.g. Allow Google) for the website allowed to be accessed in the Website
Description field.
4.
Enter the allowed domain name of the website, either the full name or the keywords (e.g.
TP-LINK) in the Allowed Domain Name
field. Any domain name with keywords in it
(http://www.tp-link.com) will be allowed.
5.
Select from the Effective Time drop-down list the schedule (e.g. Schedule_1) you want the
entry to take effect. If there are not suitable schedules for you, click the
Schedule
in red
below to go to the Advance Schedule Settings page and create the schedule you need.
-61-

Rate

4 / 5 based on 1 vote.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top