TL-WR842ND

300Mbps Multi-Function Wireless N Router

- 38 -

or more Wlans. If this checkbox is selected, you will have to set the following parameters as

shown in Figure 4-17. Make sure the following settings are correct.

Figure 4-17

¾

SSID(to be bridged)

- The SSID of the AP your Router is going to connect to as a client.

You can also use the search function to select the SSID to join.

¾

BSSID(to be bridged)

- The BSSID of the AP your Router is going to connect to as a

client. You can also use the search function to select the BSSID to join.

¾

Search

- Click this button, you can search the AP which runs in the current channel.

¾

Key type

- This option should be chosen according to the AP's security configuration. It

is recommended that the security type is the same as your AP's security type

¾

WEP Index

- This option should be chosen if the key type is WEP(ASCII) or

WEP(HEX).It indicates the index of the WEP key.

¾

Auth Type

- This option should be chosen if the key type is WEP(ASCII) or

WEP(HEX).It indicates the authorization type of the Root AP.

¾

Password

- If the AP your Router is going to connect needs password, you need to fill

the password in this blank.

)

Note:

If one of SSID (2~3) is enabled, the

Enable WDS

checkbox will turn gray and cannot be

enabled.

4.6.2

Wireless Security

Choose menu “

Wireless

→

Wireless Security

”, you can configure the security settings of your

wireless network.

There are five wireless security modes supported by the Router: WEP (Wired Equivalent Privacy),

WPA (Wi-Fi Protected Access), WPA2 (Wi-Fi Protected Access 2), WPA-PSK (Pre-Shared Key),

WPA2-PSK (Pre-Shared Key).

TL-WR842ND

300Mbps Multi-Function Wireless N Router

- 39 -

Figure 4-18 Wireless Security

¾

SSID -

Select the desired SSID from the drop-down list.

¾

Disable Security -

If you do not want to use wireless security, check this radio button. But it’s

strongly recommended to choose one of the following modes to enable security.

¾

WEP -

It is based on the IEEE 802.11 standard. If you check this radio button, you will find a

notice in red as show in Figure 4-19.

TL-WR842ND

300Mbps Multi-Function Wireless N Router

- 40 -

Figure 4-19 WEP

•

Type

-

you can choose the type for the WEP security on the drop-down list. The default

setting is

Automatic

, which can select

Shared Key

or

Open System

authentication type

automatically based on the wireless station's capability and request.

•

WEP Key Format

-

Hexadecimal

and

ASCII

formats are provided here

.

Hexadecimal

format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified

length.

ASCII

format stands for any combination of keyboard characters in the specified

length.

•

WEP Key

-

Select which of the four keys will be used and enter the matching WEP key that

you create. Make sure these values are identical on all wireless stations in your network.

•

Key Type

-

You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for

encryption. "Disabled" means this WEP key entry is invalid.

64-bit -

You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is

not promoted) or 5 ASCII characters.

128-bit -

You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is

not promoted) or 13 ASCII characters.

152-bit -

You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is

not promoted) or 16 ASCII characters.

)

Note:

If you do not set the key, the wireless security function is still disabled even if you have

selected Shared Key as Authentication Type.

¾

WPA /WPA2- Enterprise -

It’s based on Radius Server.

•

Version

-

you can choose the version of the WPA security on the drop-down list. The

default setting is

Automatic

, which can select

WPA (

Wi-Fi Protected Access) or

WPA2

(

WPA version 2) automatically based on the wireless station's capability and request.

•

Encryption -

You can select either

Automatic

, or

TKIP

or

AES.

)

Note:

If you check the

WPA/WPA2

radio button and choose TKIP encryption, you will find a

TL-WR842ND

300Mbps Multi-Function Wireless N Router

- 41 -

notice in red as shown in Figure 4-20.

Figure 4-20 WPA/WPA2 - Enterprise

•

Radius Server IP -

Enter the IP address of the Radius server.

•

Radius Port -

Enter the port number of the Radius server.

•

Radius Password -

Enter the password for the Radius server.

•

Group Key Update Period -

Specify the group key update interval in seconds. The value

should be 30 or above. Enter 0 to disable the update.

¾

WPA-PSK/WPA2-PSK- Personal -

It’s the WPA/WPA2 authentication type based on

pre-shared passphrase.

•

Version

-

you can choose the version of the WPA-PSK security on the drop-down list. The

default setting is

Automatic

, which can select

WPA-PSK

(Pre-shared key of WPA) or

WPA2-PSK

(Pre-shared key of WPA) automatically based on the wireless station's

capability and request.

•

Encryption

-

When

WPA-PSK

or

WPA

is set as the Authentication Type, you can select

either

Automatic

, or

TKIP

or

AES

as Encryption.

)

Note:

If you check the

WPA-PSK/WPA2-PSK

radio button and choose TKIP encryption, you will

find a notice in red as shown in

Figure 4-21

.

Figure 4-21 WPA/WPA2 – Personal

•

PSK Passphrase -

You can enter ASCII characters between 8 and 63 characters or 8 to

64 Hexadecimal characters.

•

Group Key Update Period -

Specify the group key update interval in seconds. The value

should be 30 or above. Enter 0 to disable the update.

TL-WR842ND

300Mbps Multi-Function Wireless N Router

- 42 -

Be sure to click the

Save

button to save your settings on this page.

4.6.3

Wireless MAC Filtering

Choose menu “

Wireless

→

MAC Filtering

”, you can control the wireless access by configuring

the

Wireless MAC Filtering

function, shown in Figure 4-22.

Figure 4-22

Wireless MAC Filtering

To filter wireless users by MAC Address, click

Enable

. The default setting is

Disabled

.

¾

MAC Address

-

The wireless station's MAC address that you want to filter.

¾

Status

-

The status of this entry, either

Enabled

or

Disabled

.

¾

Description -

A simple description of the wireless station.

To Add a Wireless MAC Address filtering entry, click the

Add New…

button. The "

Add or Modify

Wireless MAC Address Filtering entry

"

page will appear, shown in Figure 4-23:

Figure 4-23

Add or Modify Wireless MAC Address Filtering entry

To add or modify a MAC Address Filtering entry, follow these instructions:

1.

Enter the appropriate MAC Address into the

MAC Address

field. The format of the MAC

Address

is

XX-XX-XX-XX-XX-XX

(X

is

any

hexadecimal

digit).

For

example:

00-0A-EB-B0-00-0B.