TP-Link TL-WR741N Router Manual PDF (Setup & Configuration Guide)

Page 81 / 113 Scroll up to view Page 76 - 80

TL-WR740N/TL-WR741ND

150Mbps Wireless N Router

-74-

Then you will go back to the Schedule Settings page and see the following list.

4.12 Advanced Routing

Figure 4-74

Advanced Routing

There are two submenus under the Advanced Routing menu as shown in Figure 4-74:

Static

Routing List

and

System Routing Table

.

Click any of them, and you will be able to configure the

corresponding function.

4.12.1 Static Routing List

Choose menu “

Advanced Routing

→

Static Routing List

”, and then you can configure the

static route in the next screen (shown in

Figure 4-75

). A static route is a pre-determined path that

network information must travel to reach a specific host or network.

Figure 4-75

Static Routing

To add static routing entries:

1.

Click

Add New…

shown in

Figure 4-75

, you will see the following screen.

Figure 4-76

Add or Modify a Static Route Entry

Page 82 / 113

TL-WR740N/TL-WR741ND

150Mbps Wireless N Router

-75-

2.

Enter the following data:

¾

Destination Network

- The Destination Network is the address of the network or host that

you want to assign to a static route.

¾

Subnet Mask

-

The

Subnet Mask

determines which portion of an IP Address is the

network portion, and which portion is the host portion.

¾

Default Gateway

- This is the IP Address of the gateway device that allows for contact

between the Router and the network or host.

3.

Select

Enabled

or

Disabled

for this entry on the

Status

drop-down list.

4.

Click the

Save

button to make the entry take effect.

Other configurations for the entries:

Click the

Delete

button to delete the entry.

Click the

Enable All

button to enable all the entries.

Click the

Disable All

button to disable all the entries.

Click the

Delete All

button to delete all the entries.

Click the

view the information in the next screen.

4.12.2 System Routing Table

Choose menu “

Advanced Routing

→

System Routing Table

”, and then you can view the

System Routing Table in the next screen (shown in Figure 4-77). System routing table views all of

the valid route entries in use. The Destination IP address, Subnet Mask, Gateway, and Interface

will be displayed for each entry.

Figure 4-77

System Routing Table

¾

Destination Network

- The Destination Network is the address of the network or host to

which the static route is assigned.

¾

Subnet Mask

- The Subnet Mask determines which portion of an IP address is the network

Page 83 / 113

TL-WR740N/TL-WR741ND

150Mbps Wireless N Router

-76-

portion, and which portion is the host portion.

¾

Gateway

- This is the IP address of the gateway device that allows for contact between the

Router and the network or host.

¾

Interface

- This interface tells you either the Destination IP Address is on the

LAN & WLAN

(internal wired and wireless networks), or on the

WAN

(Internet).

4.13 Bandwidth Control

Figure 4-78 Bandwidth Control

There are two submenus under the Bandwidth Control menu as shown in Figure 4-78:

Control

Settings

and

Rules List

. Click any of them, and you will be able to configure the corresponding

function. The detailed explanations for each submenu are provided below.

4.13.1 Control Settings

Choose menu “

Bandwidth Control

→

Control Settings

”, and then you can configure the

Egress Bandwidth and Ingress Bandwidth in the next screen. Their values you configure should

be less than 100000Kbps. For optimal control of the bandwidth, please select the right Line Type

and ask your ISP for the total bandwidth of the egress and ingress.

Figure 4-79 Bandwidth Control Settings

¾

Enable Bandwidth Control -

Check this box so that the Bandwidth Control settings can take

effect.

¾

Line Type

-

Select the right type for you network connection. If you don’t know how to choose,

please ask your ISP for the information.

¾

Egress Bandwidth

- The upload speed through the WAN port

.

¾

Ingress Bandwidth -

The download speed through the WAN port.

Page 84 / 113

TL-WR740N/TL-WR741ND

150Mbps Wireless N Router

-77-

4.13.2 Rules List

Choose menu “

Bandwidth Control

→

Rules List

”, and then you can view and configure the

Bandwidth Control rules in the screen below.

Figure 4-80 Bandwidth Control Rules List

¾

Description

-

This is the information about the rules such as address range.

¾

Egress bandwidth -

This field displays the max and mix upload bandwidth through the WAN

port, the default is 0.

¾

Ingress bandwidth -

This field displays the max and mix download bandwidth through the

WAN port, the default is 0.

¾

Enable -

This displays the status of the rule.

¾

Modify -

Click

Modify

to edit the rule. Click

Delete

to delete the rule.

To add/modify a Bandwidth Control rule, follow the steps below.

1.

Click

Add New…

shown in Figure 4-80, you will see a new screen shown in Figure 4-81.

2.

Enter the information like the screen shown below.

Figure 4-81 Bandwidth Control Rule Settings

3.

Click the

Save

button.

Page 85 / 113

TL-WR740N/TL-WR741ND

150Mbps Wireless N Router

-78-

4.14 IP & MAC Binding Setting

Figure 4-82 the IP & MAC Binding menu

There are two submenus under the IP &MAC Binding menu (shown in Figure 4-82):

Binding

Settings

and

ARP List

. Click any of them, and you will be able to scan or configure the

corresponding function. The detailed explanations for each submenu are provided below.

4.14.1 Binding Settings

This page displays the

IP & MAC Binding Setting

table; you can operate it in accord with your

desire (shown in

Figure 4-83).

Figure 4-83 Binding Setting

¾

MAC Address

-

The MAC address of the controlled computer in the LAN.

¾

IP Address -

The assigned IP address of the controlled computer in the LAN.

¾

Bind

-

Check this option to enable ARP binding for a specific device.

¾

Modify

-

To modify or delete an existing entry.

When you want to add or modify an IP & MAC Binding entry, you can click the

Add New…

button

or

Modify

button, and then you will go to the next page. This page is used for adding or

modifying an IP & MAC Binding entry

(shown in Figure 4-84).

Rate

Popular TP-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share