1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TL-MR3420
    5. /
  5. 7
Page 31 / 121 Scroll up to view Page 26 - 30
TL-MR3420
3G/3.75G Wireless N Router
-24-
The QSS Configuration Screen of Wireless Adapter
)
Note:
In this example, the default PIN code of this adapter is 16952898 as the above figure shown.
Method Two:
Enter the PIN from my Router
Step 1: Get the Current PIN code of the Router in
Figure 4-2
(each Router has its unique PIN
code. Here takes the PIN code 12345670 of this Router for example).
Step 2: For the configuration of the wireless adapter, please choose
Enter a PIN from my
access point
in the
configuration utility of the QSS as below, and enter the PIN code of
the Router into the field behind
Access Point PIN
. Then click
Next.
The QSS Configuration Screen of Wireless Adapter
Page 32 / 121
TL-MR3420
3G/3.75G Wireless N Router
-25-
)
Note:
The default PIN code of the Router can be found in its label or the QSS configuration screen as
Figure 4-2.
c).
You will see the following screen when the new device successfully connected to the
network.
)
Note:
1)
The status LED on the Router will light green all the time if the device has been successfully
added to the network.
2)
The QSS function cannot be configured if the Wireless Function of the Router is disabled.
Please make sure the Wireless Function is enabled before configuring the QSS.
4.5
Network
Figure 4-4
the Network menu
There are five submenus under the Network menu (shown in Figure 4-4):
Internet Access
,
3G
,
WAN
,
MAC Clone
and
LAN
.
Click any of them, and you will be able to configure the
corresponding function.
4.5.1 Internet Access
Choose menu “
Network
→
Internet Access
”, you can configure the access mode on the screen
below. The router is designed to work with either WAN port or 3G USB modem, and supports
automatically take over back up with 3G access as Ethernet WAN failover.
Page 33 / 121
TL-MR3420
3G/3.75G Wireless N Router
-26-
Figure 4-5
Internet Access Mode
¾
3G Preferred
In this mode, the router will try 3G access first;
When 3G access fails and WAN access is valid, or when no 3G USB modem is inserted, the
router would switch to WAN access;
When the router succeeds to connect to the 3G network, the router would stop the WAN
connection and switch back to 3G access immediately.
¾
3G Only
In this mode, the router will try 3G access only. WAN access is disabled.
¾
WAN Preferred
In this mode, the router will try WAN access first;
When the WAN access fails, and 3G access is valid, the router would switch to 3G access;
When the router succeeds to connect to the WAN network, the router would stop the 3G
connection and switch back to WAN access immediately.
¾
WAN Only
In this mode, the router will try WAN access only. 3G access is disabled.
Click the
Save
button to save your settings.
)
Note:
1)
In 3G preferred and WAN preferred modes, until 2010-5-18, the failover/backup function only
works between 3G link and PPPoE / Dynamic IP / Static IP.
2)
The failover/backup feature between 3G link and BigPond Cable / PPTP / L2TP will be
available in the near future. Please visit our website to download the latest firmware:
3)
If you are using the
3G Preferred
or
WAN Preferred
, the router would connect, disconnect or
switch the current access automatically. The Connect/Disconnect button (on 3G, PPPoE,
PPTP, L2TP) and some related parameters could not be set manually.
Page 34 / 121
TL-MR3420
3G/3.75G Wireless N Router
-27-
4.5.2 3G
Choose menu “
Network
→
3G
”, you can configure parameters for 3G function on the screen below.
To use the 3G function, you should first insert your USB modem on the USB port of the Router.
There are already much 3G USB modem information embedded in the router. The USB modem
parameters will be set automatically if the card is supported by the Router. Take E220 for example.
If your USB modem inserted is supported by the Router, then your modem model will be shown in
the 3G USB Modem field as shown in Figure 4-6. Otherwise, “Unknown Modem” will be shown
instead as shown in Figure 4-7. Please visit our website http://www.tp-link.com to get the latest
USB modems compatibility list.
)
Note
:
3G settings are unavailable when the Internet Access mode is set to WAN Only mode. Please
change settings on
Internet Access
if you want to use 3G.
Page 35 / 121
TL-MR3420
3G/3.75G Wireless N Router
-28-
Figure 4-6
3G
Figure 4-7
¾
Location
-
Please select the location where you're enjoying the 3G card.
¾
Mobile ISP
-
Please select the ISP (Internet Service Provider) you apply to for 3G service.
The router will show the default Dial Number and APN of that ISP.

Rate

4 / 5 based on 1 vote.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top