TP-Link TL-MR3220 Router Manual PDF (Setup & Configuration Guide)

Page 21 / 109 Scroll up to view Page 16 - 20

TL-MR3220

3G/4G Wireless N Router User Guide

-12-

¾

Channel -

This field determines which operating frequency will be used. The default

channel is set to

Auto

, so the AP will choose the best channel automatically. It is not

necessary to change the wireless channel unless you notice interference problems with

another nearby access point.

¾

Mode -

This field determines the wireless mode which the Router works on.

¾

Channel Width -

Select any channel width from the pull-down list. The default setting is

automatic, which can adjust the channel width for your clients automatically.

¾

Wireless Security -

You can select one of the following security options.

z

Disable Security -

The wireless security function can be enabled or disabled. If

disabled, the wireless stations will be able to connect the Router without encryption. It

is recommended strongly that you choose one of following options to enable security.

z

WPA-Personal/WPA2-Personal -

Select WPA based on pre-shared passphrase.

Password

- You can enter

ASCII

or

Hexadecimal

characters.

For

ASCII

, the key can be made up of any numbers 0 to 9 and any letters A to Z, the

length should be between 8 and 63 characters.

For

Hexadecimal

, the key can be made up of any numbers 0 to 9 and letters A to F,

the length should be between 8 and 64 characters.

Please also note the key is case sensitive, this means that upper and lower case keys

will affect the outcome. It would also be a good idea to write down the key and all

related wireless security settings.

z

Use the Previous settings -

If you choose this option, wireless security configuration

will not change!

These settings are only for basic wireless parameters. For advanced settings, please refer to

Section 4.6: “Wireless

”.

6.

Click

Finish

or

Reboot

on the Finish page.

If you don’t make any changes on the above

Wireless

page, you will see the

Finish

page

as shown in Figure 3-7. Click the

Finish

button to finish the

Quick Setup

.

Figure 3-7

Quick Setup – Finish

If there is something changed on the above

Wireless

page, you will see the

Finish

page

as shown in Figure 3-8. Click the

Reboot

button to make your wireless configuration to

take effect and finish the

Quick Setup

.

Page 22 / 109

TL-MR3220

3G/4G Wireless N Router User Guide

-13-

Figure 3-8

Quick Setup – Finish

After the rebooting, please check whether you can access the Internet or not in the

4.2 Status

page.

Page 23 / 109

TL-MR3220

3G/4G Wireless N Router User Guide

-14-

Chapter 4. Configuring the Router

This chapter will show each Web page's key functions and the configuration way.

4.1 Login

After your successful login, you will see the fifteen main menus on the left of the Web-based utility.

On the right, there are the corresponding explanations and instructions.

The detailed explanations for each Web page’s key function are listed below.

4.2 Status

The

Status

page displays the current status information about the Router. All information is

read-only.

Page 24 / 109

TL-MR3220

3G/4G Wireless N Router User Guide

-15-

Figure 4-1 Status

4.3 Quick Setup

Please refer to

Section 3.2: "Quick Installation Guide."

4.4 WPS

This section will guide you to add a new wireless device to an existing network quickly by

WPS

(

W

i-Fi

P

rotected

S

etup)

function.

a).

Choose menu “

WPS

”, you will see the next screen (shown in

Figure 4-2

).

Page 25 / 109

TL-MR3220

3G/4G Wireless N Router User Guide

-16-

Figure 4-2

WPS

¾

WPS Status -

Enable or disable the WPS function here.

¾

Current PIN -

The current value of the Router's PIN displayed here. The default PIN of the

Router can be found in the label or User Guide.

¾

Restore PIN -

Restore the PIN of the Router to its default.

¾

Gen New PIN -

Click this button, and then you can get a new random value for the

Router's PIN. You can ensure the network security by generating a new PIN.

¾

Add Device -

You can add the new device to the existing network manually by clicking

this button.

b).

To add a new device:

If the wireless adapter supports Wi-Fi Protected Setup (WPS) or QSS (Quick Secure Setup),

you can establish a wireless connection between wireless adapter and Router by using either

Push Button Configuration (PBC) method or PIN method.

)

Note:

To build a successful connection by WPS, you should also do the corresponding configuration

of the new device for WPS function meanwhile.

For the configuration of the new device, here takes the Wireless adapter of our company for

example.

I.

By PBC (Push Button Configuration)

If the wireless adapter supports Wi-Fi Protected Setup or Quick Secure Setup and the PBC

method, you can add it to the network by PBC with the following two methods.

Method One:

Step 1: Press the

WPS/RESET

button on the rear panel of the Router.

Step 2:

Press and hold the WPS or QSS button of the adapter directly for 2 or 3 seconds.

Rate

Popular TP-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share