1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-W9980
    5. /
  5. 9
Page 41 / 123 Scroll up to view Page 36 - 40
TD-W9980
N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide
31
PPP Username/Password/Confirm Password
: Enter the User Name, Password and
Confirm Password provided by your ISP. These fields are case-sensitive.
Connection Mode:
For PPPoE connection, you can select
Always on
or
Connect on
demand
or
Connect manually
. Connect on demand is dependent on the traffic. If there is no
traffic (or
Idle
) for a pre-specified period of time, the connection will tear down automatically.
And once there is traffic send or receive, the connection will be automatically on.
Authentication Type
: Select the
Authentication Type
from the drop-down list, the default
method is
AUTO_AUTH
, and you can leave it as a default setting.
Enable IPv4:
Check this box to enable IPv4.
Enable IPv6:
Check this box to enable IPv6.
Default Gateway:
Select a WAN connection from the drop-down list as the IPv4 default
gateway.
IPv6 Default Gateway:
Select a WAN connection from the drop-down list as the IPv6 default
gateway.
Click
Advance
, advanced selections for WAN Service Setup can be shown.
Service Name/Server Name
: Enter the Service Name and Server Name if it was provided by
your ISP. You can leave them blank, if the ISP doesn’t provide them.
MTU (bytes):
Maximum Transmission Unit Size. Check this box then you can change the
MTU size. The default
MTU
value is 1500 Bytes. It is not recommended that you change the
default value unless required by your ISP.
Enable Fullcone NAT
: It is a type of NAT, if not enabled, the default NAT will act.
Enable SPI Firewall:
A SPI firewall enhances network’s security. Select the option to use a
firewall, or else without a firewall.
Enable
IGMP Proxy
: IGMP (Internet Group Management Protocol) is used to manage
multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for
client devices, such as the modem router. The default value is disabled, and if you are not
sure, please contact your ISP or just leave it.
Use IP address specified by ISP:
Choose “Use IP address specified by ISP”, you can enter
the IP address provided by your ISP.
Set DNS Server manually:
Choose
“Set DNS Server manually”, you can set DNS Server
manually here. The modem router will use this DNS Server for priority.
Use IPv6 address specified by ISP:
Choose “Use IPv6 address specified by ISP”, you can
enter the IPv6 address provided by your ISP.
Set IPv6 DNS Server manually:
Choose
“Set IPv6 DNS Server manually”, you can set IPv6
DNS Server manually here. The modem router will use this IPv6 DNS Server for priority.
Click the
Save
button to save the settings.
4)
PPPoA
If your ISP provides a
PPPoA
connection and you need to use an ATM Interface, choose
PPPoA
in the drop-down list, and then the screen will be displayed as below.
The configuration is similar to
PPPoE
. Please refer to the section
3) PPPoE
to configure this part.
Page 42 / 123
TD-W9980
N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide
32
Figure 4-14
5)
IPoA
If your ISP provides an IPoA connection, select
IPoA
option for the
Connection Type
on the
screen.
Page 43 / 123
TD-W9980
N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide
33
Figure 4-15
IP Address/Subnet Mask:
Enter the IP Address and Subnet Mask provided by ISP. If you
forget, you can ask your ISP.
DNS Server/Secondary DNS Server:
Type in your preferred DNS server.
Default Gateway:
Select a WAN Interface from the drop-down list as the IPv4 default
gateway.
6)
Bridge
If you select this type of connection, the modem router can be configured to act as a bridging
device between your LAN and your ISP. Bridges are devices that enable two or more networks to
communicate as if they are two segments of the same physical LAN.
Page 44 / 123
TD-W9980
N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide
34
Figure 4-16
Note:
After you finishing the Internet configuration, please click
Save
to make the settings take effect.
4.5.2 Interface Grouping
Choose “
Network
”
“
Interface
Grouping
”, you can view all the current groups on this page
(shown in Figure 4-17).
Figure 4-17
Enable the Virtual LAN Ports feature:
Virtual LAN (VLAN) is a group of devices on one or
more LANs that are configured so that they can communicate as if they were attached to the
same LAN. Because VLANs are based on logical instead of physical connections, it is very
flexible for user/host management, bandwidth allocation and resource optimization. If you
want to active Interface Grouping function, please check the box to enable the Virtual LAN
Ports feature.
Note:
It is not allowed to disable the VLAN with Ethernet Connection enabled.
Page 45 / 123
TD-W9980
N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide
35
To support this feature, you must create mapping groups with appropriate LAN and WAN
interfaces using the
Add
button. The
Remove
button will remove the grouping and add the
ungrouped interfaces to the Default group. Only the default group has IP interface.
Click the
Add
button. You can add a new interface group in the next screen. For example, you
want LAN1 and LAN3 to be a group called Group 1 over br_ptm_1_0 WAN interface, you can refer
to the following figure.
Figure 4-18
Click
Save
to make the entry effective immediately
4.5.3 LAN Settings
Choose “
Network
”
“
LAN Settings
” menu, and you will see the LAN screen (shown in Figure
4-19). Please configure the parameters for LAN ports according to the descriptions below.

Rate

3.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top