1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-W9980
    5. /
  5. 8
Page 36 / 123 Scroll up to view Page 31 - 35
TD-W9980
N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide
26
4.5.1.2 ADSL WAN Settings
For
ADSL
mode, there are six different configurations for the connection types, which are Static IP,
Dynamic IP, PPPoE, PPPoA, IPoA and Bridge. You can select the corresponding types according
to your needs.
Figure 4-9
Click
Add
to add a new entry, you can configure the parameters for PTM and WAN Service in the
next screen (shown in Figure 4-10).
Figure 4-10
DSL Modulation Type:
DSL Modulation Type:
The modem router supports two modulation types: ADSL and VDSL,
you can select the corresponding types according to your needs.
ATM Configuration:
VPI (0~255):
Identifies the virtual path between endpoints in an ATM network. The valid range
is from 0 to 255. Please input the value provided by your ISP.
VCI (1~65535):
Identifies the virtual channel endpoints in an ATM network. The valid range is
from 1 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value
provided by your ISP.
Page 37 / 123
TD-W9980
N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide
27
1)
Static IP
Select this option if your ISP provides static IP information to you. You should set static IP address,
IP subnet mask, and gateway address in the screen below.
Figure 4-11
Click
Advance
, advanced selections of ATM Configuration can be shown.
Encapsulation Mode:
Select the encapsulation mode for the Static IP Address. Here you
can leave it default.
ATM Qos Type:
Select ATM Qos Type provided by ISP, and the type is UBR by default.
WAN Service Setup:
Enable IPv4
：
Check the box to enable IPv4.
IP Address:
Enter the IP address in dotted-decimal notation provided by your ISP.
Subnet Mask:
Enter the subnet Mask in dotted-decimal notation provided by your ISP,
usually is 255.255.255.0.
Default Gateway
(Optional): Enter the gateway IP address in dotted-decimal notation
provided by your ISP.
DNS Server/ Secondary DNS Server:
Here you can set DNS Server (at least one) manually.
The Route will use this DNS Server for priority.
Enable IPv6:
Check the box to enable IPv6.
IPv6 Address:
Enter the IPv6 address provided by your ISP.
Page 38 / 123
TD-W9980
N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide
28
Prefix Length:
Enter the prefix length of the IPv6 address. The default value is 64.
IPv6 Gateway:
Enter the gateway IPv6 address provided by your ISP.
IPv6 DNS Server / Secondary IPv6 DNS Server:
Here you can set IPv6 DNS Server (at
least one) manually. The Route will use this IPv6 DNS Server for priority.
Default Gateway:
Select a WAN Interface from the drop-down list as the IPv4 default
gateway.
IPv6 Default Gateway:
Select a WAN Interface from the drop-down list as the IPv6 default
gateway.
Click
Advance
, advanced selections of WAN Service Setup can be shown.
MTU (bytes):
Maximum Transmission Unit Size. Check this box then you can change the MTU
size. The default
MTU
value is 1500 Bytes. It is not recommended that you change the default
value unless required by your ISP.
Enable NAT:
This technology translates the IP addresses of a local area network to a different
IP address for the Internet. If this modem router is hosting your network’s connection to the
Internet, please select the check box. If another Router exists in your network, you don’t need
to select the option.
Enable Fullcone NAT:
It is a type of NAT, if not enabled, the default NAT will act.
Enable SPI Firewall:
A SPI firewall enhances network’s security. Select the option to use a
firewall, or else without a firewall.
Enable
IGMP Proxy
: IGMP (Internet Group Management Protocol) is used to manage
multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for
client devices, such as the modem router. The default value is disabled, and if you are not sure,
please contact your ISP or just leave it.
Click the
Save
button to save the settings.
2)
Dynamic IP
Select this option, the modem router will be able to obtain IP network information dynamically from
a DHCP server provided by your ISP.
Page 39 / 123
TD-W9980
N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide
29
Figure 4-12
Click
Advance
, advanced selections for WAN Service Setup can be shown.
MTU (bytes):
Maximum Transmission Unit Size. Check this box then you can change the MTU
size. The default
MTU
value is 1500 Bytes. It is not recommended that you change the default
value unless required by your ISP.
Enable NAT:
This technology translates the IP addresses of a local area network to a different
IP address for the Internet. If this modem router is hosting your network’s connection to the
Internet, please select the check box. If another Router exists in your network, you don’t need
to select the option.
Enable Fullcone NAT
: It is a type of NAT, if not enabled, the default NAT will act.
Enable SPI Firewall:
A SPI firewall enhances network’s security. Select the option to use a
firewall, or else without a firewall.
Enable
IGMP Proxy
: IGMP (Internet Group Management Protocol) is used to manage
multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for
client devices, such as the modem router. The default value is disabled, and if you are not sure,
please contact your ISP or just leave it.
Get IP with Unicast:
This is disabled
by default. The minority of DHCP Server of ISP will not
support to enable this. When the Route is connected right but IP cannot get, you can select this
box.
Page 40 / 123
TD-W9980
N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide
30
Set DNS Server manually:
Choose
“Set DNS Server manually”, you can set DNS Server
manually here. The modem router will use this DNS Server for priority.
Get IPv6 Address with Unicast:
This is disabled
by default. The minority of DHCPv6 Server
of ISP will not support to enable this. When the modem router is connected right but IPv6
address cannot get, you can select this box.
Set IPv6 DNS Server manually:
Choose
“Set IPv6 DNS Server manually”, you can set IPv6
DNS Server manually here. The modem router will use this IPv6 DNS Server for priority.
Host Name:
Here displays model No. of your modem router.
Click the
Save
button to save the settings.
3)
PPPoE
If your ISP provides a
PPPoE
connection and you need to use an ATM Interface, choose
PPPoE
in the drop-down list, and then the screen will be displayed as below.
Figure 4-13

Rate

3.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top