1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-W8960Nv1.3.6
    5. /
  5. 19
Page 91 / 122 Scroll up to view Page 86 - 90
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
6.
Mixed WPA2/WPA
To configure Mixed WPA2/WPA settings, select the Mixed WPA2/WPA option from the drop-down
list. The menu will change to offer the appropriate settings. The steps to these settings are similar
to those for WPA-PSK.
Figure 4-88
7.
Mixed WPA2/WPA-PSK
To configure Mixed WPA2/WPA-PSK settings, select the Mixed WPA2/WPA-PSK option from the
drop-down list. The menu will change to offer the appropriate settings. The steps of this setting are
the same with WPA-PSK.
Figure 4-89
84
Page 92 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
4.5.3 MAC Filter
Choose “
Wireless
”
Æ
”
MAC Filter
”, you will see the screen of
Wireless--MAC
Filter
settings
shown as below.
Figure 4-90
Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting
within your network’s RADIUS. To filter wireless users by MAC Address, either permitting or
blocking access. If you do not wish to filter users by MAC Address, select Disabled.
¾
Disabled:
Select this option to disable MAC Filter function.
¾
Allow:
Select this option to enable MAC Filter function that allow wireless access by the
devices listed on this screen.
¾
Deny:
Select this option to enable MAC Filter function that block wireless access from the
devices listed on this screen.
¾
Add:
Click this button to add the MAC Address.
¾
Remove:
Select the item of the MAC Address and click this button to remove it.
When you click the
Add
button, the pop-up picture shown below, and then you can type the MAC
Address in the
MAC Address
field.
)
Note:
The form of MAC Address must be “
xx:xx:xx:xx:xx:xx
”, like “
00:13:0A:55:FF:09
”.
Figure 4-91
When you finished making changes to the MAC Filter List screen, click
Save/Apply
to save the
changes.
85
Page 93 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
4.5.4 Wireless Bridge
Choose “
Wireless
”
Æ
”
Wireless Bridge
”, you will see the screen of
Wireless--Bridge
settings
shown as below. You can configure wireless bridge features of the wireless LAN interface and
click
Apply/Save
button to save the current configuration.
Figure 4-92
¾
AP Mode
:
Select an AP Mode from the drop-down list. Options available are: Access Point
and Wireless Bridge.
•
Access Point
: Select this option to allow wireless stations including AP clients to access.
•
Wireless Bridge
: Also known as WDS (Wireless Distribution System), it will bridges the
wireless stations which also in bridge mode to connect two or more remote LANs.
¾
Bridge Restrict
:
•
Disabled
: Select this option to disables wireless bridge restriction, that any wireless bridge
will be granted access.
•
Enabled
: Select this option (as shown below) to enables wireless bridge restriction, please
enter the MAC address of the Remote Bridges that you want to connect with, and only
these Remote Bridges are granted access.
Figure 4-93
86
Page 94 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
•
Enabled (Scan)
: Select this option to enables wireless bridge restriction, and it will scan
the environment for APs that exist around the device. Only those selected AP will be
granted access.
•
Refresh:
Click this button to scan and display the APs.
Figure 4-94
)
Note:
Only Open or Shared authentication method support wireless bridge, you should choose
“
Wireless
”
Æ
“
Security
” to change authentication method to “open” or ”shared” mode first.
4.5.5 Advanced
Choose “
Wireless
”
Æ
”
Advanced
”, you will see the screen of
Wireless--Advanced
settings shown
as below.
87
Page 95 / 122
TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-95
¾
Channel:
Select the channel you want to use from the drop-down List. This field determines
which operating frequency will be used. It is not necessary to change the wireless channel
unless you notice interference problems with another nearby access point.
¾
Mode
: In the drop-down list you can select “11b”, “11bg”, “11bgn” and "11n only”. “11bgn”
allows both 802.11b, 802.11g and 802.11n wireless stations to connect to the Router.
¾
Bandwidth
: Select the Bandwidth you want to use from the drop-down List. If bigger
bandwidth is selected, device could transmit and receive data with higher speed.
¾
Control Sideband
: If bigger bandwidth is selected, this option will allow you select the
Control Sideband you want.
¾
Fragmentation Threshold:
This value specifies the maximum size for a packet before data
is fragmented into multiple packets. If you experience a high packet error rate, you may
slightly increase the Fragmentation Threshold. Setting the Fragmentation Threshold too low
may result in poor network performance. Only minor reduction of the default value is
recommended. In most cases, it should remain at its default value of 2346.
¾
RTS Threshold:
Should you encounter inconsistent data flow, only minor reduction of the
default value 2347 is recommended. If a network packet is smaller than the preset RTS
threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to
Send (RTS) frames to a particular receiving station and negotiates the sending of a data
frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS)
frame to acknowledge the right to begin transmission. In most cases, keep its default value of
2347.
¾
DTIM Interval:
This value, between 1 and 255, indicates the interval of the Delivery Traffic
Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next
window for listening to broadcast and multicast messages. When the Router has buffered
broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM
88

Rate

4.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top