1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-W8960NB
    5. /
  5. 6
Page 26 / 110 Scroll up to view Page 21 - 25
TD-W8960NB
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-6
¾
Remove:
Select the check box in the table on the screen above and then click the
Remove
button, the corresponding interface will be deleted in the table.
)
Note:
One ETH is allowed to configure as the layer 2 WAN Interface.
4.4.2 WAN Service
Choose “
Advanced Setup
”
Æ
“
WAN Service
”, and you will see the WAN Port Information Table in
the screen similar to Figure 4-7, which describes the WAN port settings and the relevant
manipulation to each interface. After you add a new Lay2 Interface, please follow the instructions
below to complete the further configuration of WAN Interface. There are five different
configurations for the connection types, which are PPPoE, IPoE, Bridge, PPPoA, and IPoA. You
can select the corresponding types according to your needs.
Figure 4-7
19
Page 27 / 110
TD-W8960NB
300Mbps Wireless N ADSL2+ Modem Router User Guide
)
Note:
1) The following section adopts different VPI, VCI to introduce further configuration for the
different connection types, if you need to change the configuration of ATM PVC (VPI/VCI), you
should go to the previous section (
4.4.1
Layer2 Interface
) to configure them again.
2) ETH and ATM service can not coexist. If the ETH Interface had configured, you cannot
configure any other WAN service over the ATM Interface until the ETH Interface is deleted.
4.4.2.1 ATM-EoA-PPPoE
If your ISP provides a
PPPoE
connection and you need to use an ATM Interface, follow the steps
below to add a WAN service over a selected ATM interface:
1.
Add a
new
ATM interface and select
EoA
option for DSL Link Type (
4.4.1.1
ATM interface
).
2.
Click the
Add
button on the screen Figure 4-7 and you will enter the next screen as shown in
Figure 4-8. Click
Next
.
Figure 4-8
3.
Select the
WAN service type
in Figure 4-9. If your ISP provides a PPPoE connection, select
PPPoE
option. You can create a service name for the
Service Description
or leave it the
default name. Click
Next
.
Figure 4-9
20
Page 28 / 110
TD-W8960NB
300Mbps Wireless N ADSL2+ Modem Router User Guide
4.
Enter the following parameters and then click
Next
.
Figure 4-10
¾
PPP Username/Password
: Enter the User Name and Password provided by your ISP.
These fields are case-sensitive.
¾
PPPoE Service Name
: Enter the Service Name if it was provided by your ISP. If you leave it
blank, the default name will be the same as the
Service Description
on the previous screen.
¾
Authentication Method
: Select the
Authentication Method
from the drop-down list, the
default method is
AUTO
, and you can leave it as a default setting.
)
Note:
If you are not sure about the
PPP IP extension
and
PPP Debug Mode
etc. below, please don’t
select these options.
¾
MTU Size
: Maximum Transmission Unit Size. Check this box then you can change the MTU
size. The default
MTU
value is 1480 Bytes. It is not recommended that you change the default
value unless required by your ISP.
¾
Enable Fullcone NAT
: It is a type of NAT, if not enabled, the default NAT will act.
¾
Dial on demand (with idle timeout timer)
: The Router will cut off the Internet connection after
it has been inactive for a specific period of time (idle timeout), and it will automatically
re-establish the connection as soon as you attempt to access the Internet again. If your
Internet is charged by time you may want to select this option in order to save money.
¾
PPP IP extension
: Select this option to get the public IP address from the PPP server to your
21
Page 29 / 110
TD-W8960NB
300Mbps Wireless N ADSL2+ Modem Router User Guide
PC, and the NAT and SPI Firewall will be closed. Sometimes you can think it as bridge while
PPP dialing in the router. It’s a special feature deployed by some ISP. Unless your ISP
specifically requires this setup, do not select it.
¾
Use Static IPv4 Address
: If your ISP gives you a static
WAN
,
Gateway
and
DNS
IP address,
select this option to enter them manually.
¾
Enable PPP Debug Mode
: Select this option to debug the PPP function and you can see
many PPP log information in the System Log. Only PPP has this debug Mode.
¾
Bridge PPPoE Frames Between WAN and Local Ports
: Select this option to start PPP
connection in your local PC.
¾
Enable
IGMP Multicast Proxy
: IGMP (Internet Group Management Protocol) is used to
manage multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote
configuration for client devices, such as the Router. The default value is disabled, and if you
are not sure, please contact your ISP or just leave it.
5.
Select a preferred wan interface as the system default gateway in Figure 4-11 and click
Next
.
Figure 4-11
6.
Configure the DNS Server Addresses on the screen below and click
Next
.
Figure 4-12
¾
Obtain DNS info from a WAN Interface:
You can select this option to automatically get DNS
server information from the selected WAN interface.
¾
Use the following Static DNS IP Address:
You can select this option to manually enter the
primary and /or optional secondary DNS server IP addresses provided by your ISP.
22
Page 30 / 110
TD-W8960NB
300Mbps Wireless N ADSL2+ Modem Router User Guide
)
Note:
If only single PVC with IPoA is configured, you must enter static DNS server IP addresses.
7.
On the next screen you will see the detailed settings you’ve made. Please click the
Apply/Save
button to save these settings.
Figure 4-13
8.
On the next screen you will see the WAN Port Information Table with the new configuration.
Figure 4-14
¾
Remove:
Select the check box in the table above and then click
Remove
, the corresponding
interface will be deleted in the table.
23

Rate

4 / 5 based on 1 vote.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top