Page 16 / 94
Scroll up to view Page 11 - 15
TD-W8951NB
150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide
8
• PHONE: Connect to the phone sets
• MODEM: Connect to the ADSL port of TD-W8951NB
Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of
TD-W8951NB. Connect the other end to the MODEM port of the external splitter.
Step 2:
Connect the Ethernet cable. Attach one end of a network cable to your computer’s
Ethernet port or a regular hub/switch port, and the other end to the LAN port on the
TD-W8951NB.
Step 3:
Power on the computers and LAN devices.
Step 4:
Attach the power adapter. Connect the power adapter to the power connector on the rear
of the device and plug in the adapter to a electrical outlet or power extension. The
electrical outlet shall be installed near the device and shall be easily accessible.
Figure 2-4
Page 17 / 94
TD-W8951NB
150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide
9
Chapter 3. Quick Installation Guide
3.1
Configure PC
After you directly connect your PC to the TD-W8951NB or connect your adapter to a Hub/Switch
which has connected to the Router, you need to configure your PC’s IP address. Follow the steps
below to configure it.
Step 1:
Click the
Start
menu on your desktop, right click
My Network Places
, and then select
Properties
(shown in Figure 3-1).
Figure 3-1
Step 2:
Right click
Local Area Connection
(LAN), and then select
Properties
.
Page 18 / 94
TD-W8951NB
150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide
10
Figure 3-2
Step 3:
Select
General
tab, highlight Internet Protocol (TCP/IP), and then click the
Properties
button.
Figure 3-3
Page 19 / 94
TD-W8951NB
150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide
11
Step 4:
Configure the IP address as Figure 3-4 shows. After that, click
OK
.
Figure 3-4
)
Note:
You can configure the PC to get an IP address automatically, select “Obtain an IP address
automatically” and “Obtain DNS server address automatically” in the screen above.
Now, you can run the Ping command in the command prompt to verify the network connection.
Please click the
Start
menu on your desktop, select
run
tab, type
cmd or command
in the field
and press
Enter
. Type
on the next screen, and then press
Enter
.
If the result displayed is similar to the screen below, the connection between your PC and the
Router has been established.
Page 20 / 94
TD-W8951NB
150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide
12
Figure 3-5
If the result displayed is similar to the screen shown below, it means that your PC has not
connected to the Router.
Figure 3-6
You can check it following the steps below:
1)
Is the connection between your PC and the Router correct?
The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should
be lit.
2)
Is the TCP/IP configuration for your PC correct?
If the Router's IP address is
192.168.1.1, your PC's IP address must be within the range of
192.168.1.2 ~ 192.168.1.254.
3.2
Login
Once your host PC is properly configured, please proceed as follows to use the Web-based Utility:
Start your web browser and type the private IP address of the Router in the URL field:
192.168.1.1
.
After that, you will see the screen shown below, enter the default User Name
admin
and the
default Password
admin
,
and then click
OK
to access to the
Quick Start
screen. You can follow
the steps below to complete the Quick Start.
19216811.live