1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. Archer D9 v2
    5. /
  5. 18
Page 86 / 120 Scroll up to view Page 81 - 85
82
Chapter 12
Specify Your Network Settings
8 ) Enter the
Pre-Shared Key
for IKE authentication. Then
keep
Perfect Forward Secrecy
enabled.
Note:
The key should consist of visible characters without blank space.
Make sure Site A and Site B use the same key.
9 ) Leave the
Advanced
Settings as default value. Then click
OK
to save.
3°
Configuration on Site B (remote network). Refer to step 2
configuration on Site A and make sure that Site A and Site B
use the same
pre-shared keys
and
Perfect Forward Secrecy
settings.
4°
The
Status
column will change to
UP
if the VPN connection
has been set up successfully.
5°
Check the VPN connection. You can ping site B’ LAN IP
from your computer in site A to verify that the IPSec VPN
connection is set up correctly.
Tips:
To check the VPN connection, you can do the following.
On the host in Site A, press
[Windows Logo]
+
[R]
to open Run dialog. Input “
cmd
”
and hit
OK.
In the CLI window, type in “ping 192.168.2.x” (“192.168.2.x”
can be IP address of any host in Site B). Then press [Enter].
Page 87 / 120
83
Chapter 12
Specify Your Network Settings
If Ping proceeds successfully (gets replies from host in Site B),
the IPSec connection is working properly now.
Now IPSec VPN is implemented to establish a connection.
Note:
1. The product supports a maximum of ten simultaneous connections.
2.
If one of the site has been off line for a while, for example, if Site A has been disconnected, on Site B you need to
click
Disable
and then click
Enable
after Site A back on line in order to re-establish the IPSec tunnel.
12° 7°
Set Up the IPv6 Tunnel
The IPv6 Tunnel feature helps you obtain IPv6 resources based on an IPv4 WAN
connection or vice versa.
IPv6 Tunnel is a transition mechanism that enables IPv6-only hosts to reach IPv4
services or vice versa and allows isolated IPv6 hosts and networks to reach each other
over IPv4-only infrastructure before IPv6 completely supplants IPv4. It is a temporary
solution for networks that do not support native dual-stack, where both IPv6 and IPv4
run independently.
The modem router provides three tunneling mechanisms:
6to4
,
6rd
and
DS-Lite
. The
way to set up 6rd and DS-Lite tunnel are similar.
12° 7° 1°
Use the Public IPv6 Tunnel Service-6to4
The 6to4 tunnel is a kind of public service. If there is any 6to4 server in your network,
you can use this mechanism to access IPv6 service. If your ISP provides you with an
IPv4-only connection but you want to visit IPv6 websites
,
you can try to set up a 6to4
tunnel.
Done!
Page 88 / 120
84
Chapter 12
Specify Your Network Settings
Set up the IPv6 tunnel though my ISP doesn’t provide me with
the tunnel service.
1°
Visit
http://tplinkmodem.net
, and log in with the password
you set for the modem router.
2°
Go to
Advanced
>
Network
>
IPv6 Tunnel
.
3°
Tick the check box, select
6to4
as the tunneling mechanism
and select a WAN connection from the drop-down list, then
click
Save
.
Note:
If there is no available WAN connection to choose, make sure you have connected to
the Internet and the connection type is not Bridge.
Now you can visit the IPv6 websites with the 6to4 tunnel.
Note:
Still not being able to access IPv6 resources means that not any 6to4 public server was found in your network. You
can contact your ISP to sign up for IPv6 connection service.
12° 7° 2°
Specify the 6rd Tunnel with Parameters Provided by Your ISP
Specify the 6rd tunnel with the parameters provided by my 6rd
tunnel service provider.
1°
Visit
http://tplinkmodem.net
, and log in with the password
you set for the modem router.
2°
Go to
Advanced
>
Network
>
IPv6 Tunnel
.
3°
Tick the check box, select
6RD
as the tunneling mechanism
and select a WAN connection from the drop-down list.
4°
According to the parameters provided by your ISP, choose
Auto
or
Manual
. More parameters are needed if you choose
Manual
.
5°
Click
Save
.
I want to:
How can I
do that?
Done!
I want to:
How can I
do that?
How can I
do that?
Page 89 / 120
85
Chapter 12
Specify Your Network Settings
Note:
If there is no available WAN connection to choose, make sure you have connected to
the Internet and the connection type is not Bridge.
Now you can visit the IPv6 websites with the 6rd tunnel.
Tips:
The way to set up DS-Lite tunnel is similar to that of 6rd tunnel. If you are provided with an IPv6-only WAN connection
and have signed up for DS-Lite tunnel service, specify the DS-Lite tunnel by referring to the steps above.
Done!
Page 90 / 120
Chapter
13
Administrate Your Network
This chapter introduces how to change the system settings and administrate your
modem router’s network.
This chapter contains the following sections:
•
Set System Time and Region
•
Update the Firmware
•
Back up and Restore Configuration Settings
•
Change the Administrator Account
•
Local Management
•
Remote Management
•
System Log
•
Monitor the Internet Traffic Statistics
•
CWMP Settings
•
SNMP Settings

Rate

4.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top