TP-Link Archer D9 v2 Router Manual PDF (Setup & Configuration Guide)

Page 76 / 120 Scroll up to view Page 71 - 75

72

Chapter 12

Specify Your Network Settings

4°

Set the time. Drag the cursor to cover the time area and click

Save

to make the

settings effective. The selected time will be in green.

5°

Repeat steps 3 and 4 to set time for 5GHz wireless network.

Note:

1.

If you just set time for one wireless band, the other wireless band is still always on, so set time for both of the two

bands to schedule your whole wireless network.

2.

The wireless LED (2.4GHz , 5GHz ) will turn off if the corresponding wireless network is disabled.

3. The wireless network will be automatically turned on after the time period you set.

12° 2° 4°

View Wireless Information

¾

To view the detailed wireless network settings:

1°

Visit

http://tplinkmodem.net

, and log in with the password you set for the modem

router.

2°

Go to

Advanced

>

Status

page. You can see the

Wireless

box.

3°

Select 2.4GHz or 5GHz to view the wireless details.

Page 77 / 120

73

Chapter 12

Specify Your Network Settings

Tips:

You can also see the wrieless details by clicking the router icon on

Basic

>

Network Map

.

¾

To view the detailed information of the connected wireless clients:

1°

Visit

http://tplinkmodem.net

, and log in with the password you set for the modem

router.

2°

Go to

Advanced

>

Wireless

>

Statistics

page.

3°

You can view the detailed information of the wireless clients, including its connected

wireless band and security option as well as the packets transmitted.

Tips:

You can also see the wrieless details by clicking the wireless clients icon on

Basic

>

Network Map

.

12° 2° 5°

Advanced Wireless Settings

Advanced wireless settings are for those who have a network concept. If you are not

familiar with the settings on this page, it’s strongly recommended that you keep the

provided default values; otherwise it may result in lower wireless network performance.

1°

Visit

http://tplinkmodem.net

, and log in with the password you set for the modem

router.

2°

Go to

Advanced

>

Wireless

>

Advanced Settings

page.

Page 78 / 120

74

Chapter 12

Specify Your Network Settings

•

Beacon Interval:

Enter a value between 25 and 1000 in milliseconds to determine the

duration between which beacon packets are broadcasted by the router to synchronize

the wireless network. The default is 100 milliseconds.

•

RTS Threshold:

Enter a value between 1 and 2346 to determine the packet size of

data transmission through the router. By default, the RTS (Request to Send) Threshold

size is 2346. If the packet size is greater than the preset threshold, the router sends

Request to Send frames to a particular receiving station and negotiates the sending

of a data frame, or else the packet will be sent immediately.

•

DTIM Interval:

Enter a value between 1 and 255 to determine the interval of the

Delivery Traffic Indication Message (DTIM). 1 indicates the DTIM Interval is the same

as

Beacon Interval

.

•

Group Key Update Period:

Enter the number of seconds to control the time interval

for the encryption key automatic renewal. The default is 0, indicating no key renewal.

•

Enable WMM:

This feature guarantees the packets with high-priority messages being

transmitted preferentially. WMM is enabled compulsively under 802.11n or 802.11ac

mode. It is strongly recommended to enable WMM.

•

Enable Short GI:

This feature is enabled by default and recommended to increase the

data capacity by reducing the Guard Interval (GI) time.

•

AP Isolation:

Select this checkbox to enable the AP Isolation feature that allows you to

confine and restrict all wireless devices on your network from interacting with each

other, but still able to access the Internet. AP isolation is disabled by default.

Page 79 / 120

75

Chapter 12

Specify Your Network Settings

•

WDS:

Select this checkbox to enable the WDS (Wireless Distribution System) Bridging

feature to allow the router to bridge with another access point (AP) in a wireless local

area network (WLAN). Refer to

T7. How to use the WDS Bridging function to extend my

wireless network?

under

Appendix B: Troubleshooting

for detailed instructions.

12° 3°

Set Up a Dynamic DNS Service Account

Most ISPs (Internet service providers) assign a dynamic IP address to the router and

you can use this IP address to access your router remotely. However, the IP address can

change any time and you don’t know when it changes. In this case, you might need

the DDNS (Dynamic Domain Name Server) feature on the router to allow you and your

friends to access your router and local servers (FTP, HTTP, etc.) using domain name, in

no need of checking and remembering the IP address.

Note:

DDNS does not work if the ISP assigns a private WAN IP address (such as 192.168.1.x) to the modem router.

To set up DDNS, please follow the instructions below:

1°

Visit

http://tplinkmodem.net

, and log in with the password you set for the modem

router.

2°

Go to

Advanced

>

Network

>

Dynamic DNS.

3°

Select the

DDNS service provider

(Dyndns or NO-IP). If you don’t have a DDNS

account, select a service provider and click

Go to register

.

4°

Enter the username, password and domain name of the account (such as lisa.ddns.

net).

5°

Click

Login

and

Save

.

Tips:

If you want to use a new DDNS account, please Logout first, then login with the new account.

12° 4°

Interface Grouping

Divide my devices connected to the modem router into different

I want to:

Page 80 / 120

76

Chapter 12

Specify Your Network Settings

groups and disallow devices’ cross-group communication.

For example

, in my house, devices connected to LAN1 and LAN3

are for work, while others for entertainment. I want to isolate

working devices from others while keep all devices’ access to

the Internet.

1°

Visit

http://tplinkmodem.net

, and log in with the password

you set for the modem router.

2°

Go to

Advanced

>

Network

>

Interface Grouping

to open the

configuration page where some interfaces can be grouped

together.

3°

Click to

Add

a new group.

4°

Name the group.

How can I

do that?

Rate

Popular TP-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share