TP-Link Archer D7 Router Manual PDF (Setup & Configuration Guide)

Page 86 / 124 Scroll up to view Page 81 - 85

Archer

D7

AC1750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide

75



Note:

RIP cannot be configured on the WAN Interface which has NAT enabled (such as PPPoE).

4.13 IPv6 Route Settings

Choose “

IPv6

Route Settings

”, it includes four menus

: IPv6 Default Gateway and IPv6 Static

Route

. The detailed descriptions are provided below.

4.13.1 IPv6 Default Gateway

Choose “

IPv6

Route Settings

”



“

IPv6

Default Gateway

”, you can see the Default Gateway

screen. You can select a WAN Interface from the drop-down list as the system default gateway.

Figure 4-68

Click the

Add Interface

button, you can add WAN Interfaces.

Click the

Save

button to save your settings.

4.13.2 IPv6 Static Route

Choose “

IPv6

Route Settings

”



“

IPv6 Static Route

”. You can see the IPv6 Static Route screen.

This screen allows you to configure the IPv6 static routes (shown in Figure 4-69). An IPv6 static

route is a pre-determined path that network information must travel to reach a specific host or

network.

Figure 4-69

To add a new entry, follow the instructions below.

1.

Click the

Add New

button in Figure 4-69, and you will see the screen as shown in Figure

4-70.

Page 87 / 124

Archer

D7

AC1750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide

76

Figure 4-70

2.

Enter the following data:



Destination IPv6 Address:

The

Destination IPv6 Address

is the address of the network or

host that you want to assign to a static route.



Prefix Length:

The prefix length of the destination IPv6 address.



Gateway:

Here you should type the IPv6 Gateway address correctly, and the option for

Interface

will adopt the default IPv6 Gateway address for the IPv6 Static Route.



Interface:

Select the Interface name from the drop-down list, or else, the default Interface will

be adopted for the IPv6 Static Route.



Status:

Select

Enabled

or

Disabled

from the drop-down list

.

3.

Click

Save

to save your settings.

To modify or delete an existing entry:

1.

Find the desired entry in the table.

2.

Click

Edit

as desired on the

Edit

column.

Click the

Enable/ Disabled Selected

button to make selected entries enabled/ disabled.

Click the

Delete Selected

button to delete the selected entries.

4.14 Forwarding

There are four submenus under the Forwarding menu:

Virtual Servers

,

Port Triggering

,

DMZ

and

UPnP

. Click any of them, and you will be able to configure the corresponding function.

Page 88 / 124

Archer

D7

AC1750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide

77

4.14.1 Virtual Servers

Choose menu “

Forwarding

”

→

“

Virtual Servers

”, and then you can view and add virtual servers

in the next screen (shown in Figure 4-71). Virtual servers can be used for setting up public

services on your LAN. A virtual server is defined as a service port, and all requests from Internet

to this service port will be redirected to the computer specified by the server IP. Any PC that was

used for a virtual server must have a static or reserved IP address because its IP address may

change when using the DHCP function.

Figure 4-71



Service Port:

The numbers of External Service Ports. You can enter a service port or a

range of service ports (the format is XXX – YYY; XXX is the Start port and YYY is the End

port).



IP Address

: The IP address of the PC running the service application.



Protocol

: The protocol used for this application, either

TCP

,

UDP

, or

All

(all protocols

supported by the modem router).



Status

: The status of this entry, "Enabled" means the virtual server entry is enabled.



Edit

: To modify or delete an existing entry.

To set up a virtual server entry:

1.

Click the

Add New

button. (pop-up

Figure 4-72)

2.

Select the service you want to use from the

Common Service Port

list. If the

Common

Service Port

menu does not list the service that you want to use, enter the number of the

service port or service port range in the

Service Port

field.

3.

Enter the IP address of the computer running the service application in the

IP Address

field.

4.

Select the protocol used for this application in the

Protocol

drop-down list, either

TCP

,

UDP

,

or

All

.

5.

Select the

Enabled

option in the

Status

drop-down list.

Click the

Save

button.

Page 89 / 124

Archer

D7

AC1750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide

78

Figure 4-72



Note:

It is possible that you have a computer or server that has more than one type of available service.

If so, select another service, and type the same IP address for that computer or server.

To modify or delete an existing entry:

1.

Find the desired entry in the table.

2.

Click

Edit

as desired on the

Edit

column.

Click the

Enable/ Disabled Selected

button to make selected entries enabled/ disabled.

Click the

Delete Selected

button to delete the selected entries.



Note:

If you set the service port of the virtual server as 80, you must set the Web management port on

System Tools –> Manage Control

page to be any other value except 80 such as 8080.

Otherwise there will be a conflict to disable the virtual server.

4.14.2 Port Triggering

Choose menu “

Forwarding

”

→

”

Port Triggering

”, you can view and add port triggering in the

next screen (shown in Figure 4-73). Some applications require multiple connections, like Internet

games, video conferencing, Internet telephoning and so on. Port Triggering is used for some of

these applications that cannot work with a pure NAT modem router.

Figure 4-73

Page 90 / 124

Archer

D7

AC1750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide

79

To add a new rule, follow the steps below.

1.

Click the

Add New

button, the next screen will pop-up as shown in Figure 4-74.

2.

Select a common application from the

Common Service Port

drop-down list, then the

Trigger Port

field and the

Open Ports

field will be automatically filled. If the

Common

Service Port

does not have the application you need, enter the

Trigger Port

and the

Open

Ports

manually.

3.

Select the protocol used for Trigger Port from the

Trigger Protocol

drop-down list, either

TCP

,

UDP

, or

All

.

4.

Select the protocol used for Incoming Ports from the

Open Protocol

drop-down list, either

TCP

or

UDP

, or

All.

5.

Select

Enable

in

Status

field.

6.

Click the

Save

button to save the new rule.

Figure 4-74



Interface

: Display the default gateway you have ser in

4.5.1 WAN Settings

.



Trigger Port

: The port for outgoing traffic. An outgoing connection using this port will trigger

this rule.



Trigger Protocol

: The protocol used for Trigger Ports, either

TCP

,

UDP

, or

All

(all protocols

supported by the modem router).



Open Port

: The port or port range used by the remote system when it responds to the

outgoing request. A response using one of these ports will be forwarded to the PC which

triggered this rule. You can input at most 5 groups of ports (or port sections). Every group of

ports must be separated with ",", for example, 2000-2038, 2046, 2050-2051, 2085,

3010-3030.



Open Protocol

: The protocol used for

Incoming Port

, either

TCP

,

UDP

, or

ALL

(all

protocols supported by the modem router).



Status

: The status of this entry, Enabled means the Port Triggering entry is enabled.



Common Service Port

: Some popular applications already listed in the drop-down list of

Open Protocol

.

Rate

Popular TP-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share