1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. Archer D5
    5. /
  5. 12
Page 56 / 127 Scroll up to view Page 51 - 55
Archer
D5
AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
45
11g only:
Select if all of your wireless clients are 802.11g.
11n only:
Select only if all of your wireless clients are 802.11n.
11bg mixed:
Select if you are using both 802.11b and 802.11g wireless clients.
11bgn mixed:
Select if you are using a mix of 802.11b, 11g, and 11n wireless clients.
When 802.11g mode is selected, only 802.11g wireless stations can be connected to the
modem router. When 802.11n mode is selected, only 802.11n wireless stations can connect
to the modem router. It is strongly recommended that you set the Mode to
802.11bgn mixed
,
and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the modem router.
Channel:
Select the channel you want to use from the drop-down list. This field determines
which operating frequency will be used. It is not necessary to change the wireless channel
unless you notice interference problems with another nearby access point.
Channel Width:
Select the channel width from the drop-down list
.
The default setting is
automatic, which can adjust the channel width for your clients automatically.
Note:
If
11b only
,
11g only
, or
11bg mixed
is selected in the
Mode
field, the
Channel Width
selecting
field will turn grey and the value will become 20M, which is unable to be changed.
Enable SSID Broadcast:
When wireless clients survey the local area for wireless networks to
associate with, they will detect the SSID broadcast by the modem router. If this checkbox is
selected, the wireless router will broadcast its name (SSID) on the air.
Enable WDS:
With this function, the modem router can bridge two or more Wlans. If this
checkbox is selected, you will need to set the following parameters as shown in the figure
below. Make sure the following settings are correct.
SSID (to be bridged):
The SSID of the AP your modem router is going to connect to as a
client. You can also use the search function to select the SSID to join.
BSSID (to be bridged):
The BSSID of the AP your modem router is going to connect to as a
client. You can also use the search function to select the BSSID to join.
Scan:
Click this button, you can search the AP which runs in the current channel.
Key type
: This option should be chosen according to the AP's security configuration. It is
recommended that the security type is the same as your AP's security type
WEP Index
: This option should be chosen if the key type is WEP(ASCII) or WEP(HEX). It
indicates the index of the WEP key.
Page 57 / 127
Archer
D5
AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
46
Authentication Type
: This option should be chosen if the key type is WEP(ASCII) or
WEP(HEX). It indicates the authorization type of the Root AP.
Password
:
If the AP your modem router is going to connect needs password, you need to fill
the password in this blank.
Click
Save
to save your settings.
4.8.2
WPS Settings
This section will guide you to add a new wireless device to an existing network quickly by
WPS
(also called
QSS
)
function.
a).
Choose menu “
WPS Settings
”, and you will see the next screen (shown in Figure 4-32).
Figure 4-32
WPS:
Enable or disable the WPS function here.
Current PIN:
The current value of the modem router's PIN is displayed here.
Restore PIN:
Restore the PIN of the modem router to its default.
Generate New PIN:
Click this button to get a new random PIN code. You can ensure the
network security by generating a new PIN.
Add device:
You can add a new device to the existing network manually by clicking this
button.
b).
To add a new device:
If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless
connection between wireless adapter and modem router using either Push Button Configuration
(PBC) method or PIN method.
Note:
To build a successful connection by WPS, you should also do the corresponding configuration of
the new device for WPS function meanwhile.
I.
Use the Wi-Fi Protected Setup Button
Use this method if your client device has a Wi-Fi Protected Setup button.
Step 1:
Press the WPS button on the back panel of the modem router, as shown in the following
figure.
Page 58 / 127
Archer
D5
AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
47
You can also keep the default WPS Status as
Enabled
and click the
Add device
button in Figure
4-32, then Choose “
Press the button of the new device in two minutes
” and click
Connect
.
(Shown in the following figure)
Figure 4-33
Step 2:
Press and hold the WPS button of the client device directly.
Step 3:
The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup
process.
Step 4:
When the WPS LED is on, the client device has successfully connected to the modem
router.
Refer back to your client device or its documentation for further instructions.
II.
Enter the client device’s PIN on the modem router
Use this method if your client device has a Wi-Fi Protected Setup PIN number.
Step 1:
Keep the default WPS Status as
Enabled
and click the
Add device
button in Figure
4-32, then the following screen will appear.
Figure 4-34
Step 2:
Enter the PIN number from the client device in the field on the above WPS screen. Then
click
Connect
button.
Step 3:
“
Connect successfully
” will appear on the screen of Figure 4-34, which means the
client device has successfully connected to the modem router.
III. Enter the modem router’s PIN on your client device
Use this method if your client device asks for the modem router’s PIN number.
Step 1:
On the client device, enter the PIN number listed on the modem router’s Wi-Fi Protected
Setup screen. (It is also labeled on the bottom of the modem router.)
Step 2:
The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected
Page 59 / 127
Archer
D5
AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
48
Setup process.
Step 3:
When the WPS LED is on, the client device has successfully connected to the modem
router.
Step 4:
Refer back to your client device or its documentation for further instructions.
Note:
1)
The WPS LED on the modem router will light green for five minutes if the device has been
successfully added to the network.
2)
The WPS function cannot be configured if the Wireless Function of the modem router is
disabled. Please make sure the Wireless Function is enabled before configuring the WPS.
4.8.3
Wireless Security
Choose menu “
Wireless 2.4GHz
”
”
Wireless Security
”, you can configure the security settings
of your wireless network.
There are three wireless security modes supported by the modem router: WPA/WPA2 – Personal,
WPA/WPA2 – Enterprise, WEP (Wired Equivalent Privacy).
Figure 4-35
Disable Wireless Security:
If you do not want to use wireless security, check this radio
button. But it’s strongly recommended to choose one of the below modes to ensure security.
WPA/WPA2-Personal:
It’s the WPA/WPA2 authentication type based on pre-shared
passphrase. It is chosen by default.
Authentication Type:
You can choose the type for the WPA/WPA2-Personal security on
the drop-down list. The default setting is
Auto
, which can select
WPA-PSK
or
WPA2-PSK
as
authentication type automatically based on the wireless station's capability and request.
Page 60 / 127
Archer
D5
AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
49
Encryption:
You can select
Auto
,
TKIP
or
AES
as Encryption.
Wireless Password:
You can enter ASCII characters between 8 and 63 characters or 8 to
64 Hexadecimal characters. The default password is the same with the default PIN code,
which is labeled on the bottom of the modem router or can be found in Figure 4-32.
Group Key Update Period:
Specify the group key update interval in seconds. The value
should be 30 or above. Enter 0 to disable the update.
WPA/WPA2 – Enterprise:
It’s based on Radius Server.
Authentication Type
:
Authentication Type:
You can choose the type for the
WPA/WPA2-Personal security on the drop-down list. The default setting is
Auto
, which can
select
WPA-PSK
or
WPA2-PSK
as
authentication type automatically based on the wireless
station's capability and request.
Encryption:
You can select
Auto
,
TKIP
or
AES
as Encryption.
RADIUS Server IP:
Enter the IP address of the Radius Server.
RADIUS Server Port:
Enter the port that radius service used.
RADIUS Server Password:
Enter the password for the Radius Server.
Group Key Update Period:
Specify the group key update interval in seconds. The value
should be 30 or above. Enter 0 to disable the update.
WEP:
It is based on the IEEE 802.11 standard.
Authentication Type:
You can choose the type for the WPA/WPA2-Personal security on
the drop-down list. The default setting is
Auto
, which can select
WPA-PSK
or
WPA2-PSK
as
authentication type automatically based on the wireless station's capability and request.
WEP Key Format:
Hexadecimal
and
ASCII
formats are provided here
.
Hexadecimal
format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified
length.
ASCII
format stands for any combination of keyboard characters in the specified
length.
WEP Key:
Select which of the four keys will be used and enter the matching WEP key that
you create. Make sure these values are identical on all wireless stations in your network.

Rate

4.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top