1. Home
    2. /
  2. Manuals
    3. /
  3. Totolink
    4. /
  4. ND300V2
    5. /
  5. 2
Page 6 / 32 Scroll up to view Page 1 - 5
- 4 -
Wireless Transmit
Power
20dBm(MAX)
Receiver Sensitivity
270M: -65dBm@10% PER
135M: -65dBm@10% PER
54M: -68dBm@10% PER
11M: -85dBm@8% PER
6M: -88dBm@10% PER
1M: -90dBm@8% PER
Channels
1-11 (North America);
1-13 (General Europe)
WLAN Modulation
Scheme
BPSK, QPSK, CCK and OFDM (BPSK/QPSK/16-QAM/ 64-QAM)
Antenna Type
2.4GHz omni antenna
Wireless Operation
Mode
Wireless Bridge /Client/ WAN /WDS
Wireless Security
WEP 64/128 bit; MAC based Association; SSID broadcast disable; Wi-Fi
Protection Access (TBD), WPA, WPA2, WPS
LED
1*Power, 1*CPU Status,
1*Wireless, 1*WAN, 4*LAN
Media
100BASE-TX: UTP/STP
Management type
Local/Remote Web-based configuration
Operating
Temperature
0 ~ 55
℃
Storage
-20 ~ 65
℃
Humidity
5 ~ 95% non-condensing
Power External
Input 110V/240V
Output DC: 5V, 2.5A (N300RG);
5V, 1A
(N150RA, N150RT,N300RT);
9V, 0.8A (N300R).
Page 7 / 32
- 5 -
Section 2: Hardware installation
2.1 Panel layout
2.1.1 Front panel
LED indicators:
Led Name
Action
Description
Off
Power off
Power
On
power on
Off
the router has a hardware error
CPU
Flashing
the router is working properly
Off
wireless function is disabled
WLAN
Flashing
wireless function is enabled
Off
there is no device connected to the corresponding port
On
there is a device connected to the corresponding port
WAN /
LAN 1, 2, 3, 4
Flashing
there is an active device connected to the corresponding port
2.1.2 Back panel
Page 8 / 32
- 6 -
DC IN
Plug in the DC power jack.
Note: Please use the original power adapter to prevent the unsuitable
power adapter damage to your router.
WAN port
WAN port (RJ-45). Connect
xDSL Modem / Cable Modem or Ethernet
LAN port
4 RJ-45 ports. PC and hub / switch connect to LAN port through cable
RST
Press this button for
five
seconds, the system will be restored to the factory
default settings.
RST/WPS
WPS
When your wireless LAN adapter connected with the wireless router, press
this button in the router, and press the “WPS” button in your wireless LAN
adapter within
two
minutes, it will generate a secret key automatically
between your LAN adapter and router, on the premise that the LAN adapter
with WPS function.
Antenna Interface
Fixed or detachable omni antenna adjust to different models
2.2 System Requirements
¾
Broadband Internet access service (DSL/Cable/Ethernet)
¾
One DSL/Cable modem that has an RJ-45 connector (you
do not need it if you
connect the router to Ethernet)
¾
Each PC on the LAN needs a working Ethernet Adapter and
an Ethernet cable with
RJ45 connectors
¾
TCP/IP protocol must be installed on each PC
¾
Web browser, such as Microsoft Internet Explorer 5.0 or later,
Netscape Navigator 6.0
or later
2.3 Installation Environment
¾
Not in direct sunlight or near a heater or heating vent
¾
Not cluttered or crowded. There should be at least 2 inches (5cm) of clear space on
all sides of the router
¾
Well ventilated (especially if it is in a closet)
¾
Operating temperature: 0
℃
~40
℃
¾
Operating Humidity: 5%~90%RH, Non-condensing
2.4 Hardware Installation Steps
Before you install the router, you should connect your PC to the Internet through your
broadband service successfully. If there is any problem, please contact your ISP. After
that, please install the router according to the following steps. Don't forget to pull out the
power plug and keep your hands dry.
1. Power off your PC(s), Cable/DSL modem, and the router.
2. Locate an optimum location for the router. The best place is usually near the center of
the area in which your PC(s) will wirelessly connect. The place must comply with the
Page 9 / 32
- 7 -
Installation Environment Requirements.
3. Adjust the direction of the antenna. Normally, upright is a good direction.
4. Connect the PC(s) and each Switch/Hub on your LAN to the LAN Ports in the router.
5. Connect the DSL/Cable Modem to the WAN port on the router.
6. Connect the DC power adapter to the power port (DC IN) in the router, and plug the
power plug in the electrical outlet. The router will begin to work automatically.
7. Power on your PC(s) and Cable/DSL modem.
Section 3:Quick Installation Guide
After connecting the wireless router into your network, you should configure it. This
chapter describes how to configure the basic functions of your wireless router. These
procedures only take you a few minutes. You can access the Internet via the router
immediately after successfully configured.
3.1 TCP/IP configuration
The default IP address of the wireless router is
192.168.1.1
, and the default Subnet Mask
is
255.255.255.0
. These values can be seen from the LAN. They can be changed as you
desire, as an example we use the default values for description in this guide.
Connect the local PC to the LAN ports in the router. There are two methods to configure
the IP address for your PC.
Configure the IP address manually
1)
Set up the TCP/IP Protocol for your PC(s).
2)
Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is from 2
to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1 (The router's
default IP address)
Obtain an IP address automatically
1)
Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your
PC(s).
2)
Power off the router and PC(s). Then turn on the router, and restart the PC(s). The
built-in DHCP server will assign IP address for the PC(s).
Now, you can run the Ping command in the command prompt to verify the network
connection between your PC(s)
and the router.
Open a command prompt, and type
ping
192.168.1.1
, and then press “enter”.
A. Click “Start” -> “Run”
B.
Type the command “cmd”, and then click "OK"
Page 10 / 32
- 8 -
C. Type “ipconfig”
and press “enter”
D. If the result displayed is similar to that shown in the below figure, the connection
between your PC and the router has been established, or else please repeat the
above steps and restart the PC.
IP address from 192.168.1.2 to 192.168.1.254
Subnet mask is 255.255.255.0 ;
Default gateway is 192.168.1.1 ;
E. Enter the command “ping 192.168.1.1”, and then press ”enter”
If you can see similar result displayed “Reply from 192.168.1.1
：
bytes=32 time<1ms
TTL=255”, it means the user's PC has been connected with the router.

Rate

4.5 / 5 based on 2 votes.

Popular Totolink Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top