Page 31 / 88 Scroll up to view Page 26 - 30
E-DOC-CTC-20080118-0051 v2.0
25
3
Adding New Devices to your Network
3.2.2
Configuring your Thomson Gateway
Introduction
If you configured your Thomson Gateway using the
Guided Installation
, the telephony service will already be
configured by the Setup wizard.
If you choose to configure your Thomson Gateway manually or you still need to configure the telephony
service, you can follow the procedure below.
Procedure
Proceed as follows:
1
Enable the Telephony Service
2
Assign Phone Numbers
3
Configure the Telephony Service
Enable the Telephony Service
To enable the telephony service:
1
Browse to the
Thomson Gateway Web Interface
.
2
On the
Toolbox
menu, click
Telephony.
3
In the
Navigation Bar
, click
Configure
.
4
Select
Service Enabled
.
5
Click
Apply
.
Assign Phone Numbers
To configure your Internet SIP telephone numbers:
1
Browse to the
Thomson Gateway Web Interface
.
2
On the
Toolbox
menu, click
Telephony
.
3
In the
Navigation Bar
, click
Configure
. Assign phone numbers to the ports. If you want to use the same
number for all ports, select Port ‘
All
’.
4
Click
Apply
.
Configure the Telephony Service
Proceed as follows to configure the telephony service:
1
Browse to the
Thomson Gateway Web Interface
.
2
On the
Toolbox
menu, click
Telephony
.
3
In the
Navigation Bar
, click
Expert configure
.
Your Internet connection must be up and running before you can configure Internet telephony.
The phone numbers are provided by your provider.
Page 32 / 88
E-DOC-CTC-20080118-0051 v2.0
26
3
Adding New Devices to your Network
4
Enter the IP address and the port number of the registrar, and the proxy, as provided by your ISP:
5
Click
Apply
.
Verifying Telephone Connectivity
Proceed as follows to verify the voice connection:
1
Make sure the Thomson Gateway is turned on and ready for service.
2
Check whether your phone is properly attached to the Thomson Gateway.
3
Make sure the Internet telephony service is enabled and configured.
4
The
Voice
LED must be solid green.
5
Pick up your phone, wait for the dialling tone, and dial the number. If you dial a ‘#’ after the phone
number, the phone number will be called instantly.
The phone(s) attached to the Thomson Gateway can receive incoming VoIP calls, as long as your
Thomson Gateway is turned on and the
Voice
LED is lit.
For calls over the analogue phone line, your phones are line-powered by the telephone company
and can therefore always be reached, even if the Thomson Gateway is turned off.
Page 33 / 88
E-DOC-CTC-20080118-0051 v2.0
27
3
Adding New Devices to your Network
3.2.3
Multiple Identities
Introduction
You can assign up to three Internet telephone numbers or URIs to one or both phone ports, or you can assign
a common number to both phone ports.
Procedure
Proceed as follows:
1
Browse to the Thomson Gateway web pages.
2
On the
Toolbox
menu, click
Telephony
.
3
In the
Navigation Bar
, click
Configure
.
4
In the
Pick a task
list
,
click
Use multiple identities
.
5
Click
Add
.
6
Enter another URI, your user name and password.
7
Choose the phone port for which you want to use this telephone number.
8
Click
Apply
.
The phone numbers are provided by your provider.
Page 34 / 88
E-DOC-CTC-20080118-0051 v2.0
28
3
Adding New Devices to your Network
Page 35 / 88
E-DOC-CTC-20080118-0051 v2.0
29
4
Getting the Most Out of Your Thomson Gateway
4
Getting the Most Out of Your Thomson Gateway
In this chapter
In this chapter we will take a closer look at following features:
Feature availability
Depending on the configuration offered by your Internet Service Provider (ISP), some features may not be
available on your Thomson Gateway. For more information, contact your ISP.
Topic
Page
Sharing Content on your Network
30
Telephony Features
39
Universal Plug and Play
46
Assigning a service (HTTP, FTP,...) to a computer
53
Dynamic DNS
55

Rate

124.8 / 5 based on 304 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top