1. Home
    2. /
  2. Manuals
    3. /
  3. Thomson
    4. /
  4. DWG855T
    5. /
  5. 2
Page 6 / 60 Scroll up to view Page 1 - 5
Page 7 / 60
Chapter 1: Connections and Setup
Illustrations contained in this document are for representation only.
1
Introduction
Residential Voice Gateway Features
z
Support Multiple Provisioning Mode
z
Standard RJ-45 connector for 10/100BaseT Ethernet with auto-negotiation and MDIS
functions
z
USB Connector for USB interface
z
Two RJ-11 Foreign Exchange Station (FXS) ports for IP telephony
z
Support simultaneous voice and data communications
z
Two simultaneous voice conversations in the different FXS ports with different CODEC:
PCM A-law, PCM-law, G.723.1, G.729, G.729a, G.729e, G.728, G.726, BV16 and BV32
z
Echo Cancellation
z
Voice Active Detection (VAD)
z
DTMF detection and generation
z
Comfort Noise Generation (CNG)
z
Support V.90 fax and modem services
z
Transparent bridging for IP traffic
z
RSA and 56 bit DES data encryption security
z
SNMP network management support
z
Remote operating firmware downloading
z
Support Web pages and private DHCP server for status monitoring
z
Clear LED display
z
Plug and Play
What’s on the CD-ROM
Insert the Residential Voice Gateway CD-ROM into your CD-ROM drive to view troubleshooting
tips, the internal diagnostics, and other valuable information.
Note: You might need to use the CD-ROM to install the USB driver if you are connecting via the
USB port.
Page 8 / 60
Chapter 1: Connections and Setup
2
CD-ROM Contents:
z
Electronic copy of this user’s guide in additional languages (PDF format)
z
Adobe Acrobat Reader — application you can load to read PDF format, if you don’t have
it loaded already
z
USB drivers — required if connecting by USB
z
Links to Thomson and RCA web sites
DOCSIS and PacketCable are trademarks of Cable Television Laboratories, Inc.
Page 9 / 60
Chapter 1: Connections and Setup
Illustrations contained in this document are for representation only.
3
Computer Requirements
For the best possible performance from your Residential Voice Gateway, your personal computer
must meet the following minimum system requirements (note that the minimum requirements
may vary by cable companies):
IBM PC COMPATIBLE
MACINTOSH**
CPU
Pentium preferred
PowerPC or higher
System RAM
16MB (32MB preferred)
24MB (32MB preferred)
Operating System
Windows* NT/2000/Me/XP,
Linux
Mac OS** 7.6.1 or higher
Available Disk Space
125MB
50MB
Sound Card
Required for audio on CD-ROM
N/A
Video
VGA or better (SVGA preferred)
VGA or better (SVGA built-in
preferred)
CD-ROM Drive
Required
Required
10BaseT or 100BaseT
10BaseT or 100BaseT
Ethernet
An Ethernet card makes it possible for your computer to pass data to
and from the internet. You must have an Ethernet card and software
drivers installed in your computer. You will also need a standard
Ethernet cable to connect the Ethernet card to your Residential Voice
Gateway.
USB (Windows 2000/ME/XP only)
USB Port
The Universal Serial Bus is a high speed bus that enables your
computer to communicate simultaneously with a variety of
peripherals. However, if you have other peripherals that send and
receive a lot of information, such as speakers, printers or scanners, we
recommend using an Ethernet card to support this modem.
Page 10 / 60
Chapter 1: Connections and Setup
4
Software
•
A TCP/IP network protocol for each machine
•
Microsoft Internet Explorer 4.0 or later or Netscape Navigator 4.0 or
later. (5.0 and 4.7 or later, respectively, are strongly
recommended.)
*Windows is a trademark of Microsoft Corporation.
**Macintosh and the Mac OS are trademarks of Apple Computer, Inc.
Wall Mounting
The number of the screw: 2 pcs
Direction for wall mounting: LED panel upward.
Dimension for the screw: TBD
There are 4 slots on the underside of the EMTA that can be used for wall mounting.
Note: When wall mounting the unit, ensure that it is within reach of the power outlet.
You will need 2 suitable screws which screw diameter would be 4.4 mm to wall mount the Cable
Modem or the Battery Pack. Two different wall mount directions could be chosen for the Battery
Pack.
To do this:
1.
Ensure that the wall you use is smooth, flat, dry and sturdy and use the 4 screw holes
which are 101.6 mm apart from each other.
2.
Fix the screws into wall, leaving their heads 3 mm (0.12 inch) clear of the wall surface.

Rate

124.8 / 5 based on 304 votes.

Popular Thomson Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top