Page 11 / 54 Scroll up to view Page 6 - 10
5
3660181C
Set-up
Setting up Your System
These are the steps to set up your system. They are described step by step in detail on the following pages; so,
when you are ready, turn the page to get started. . .
Basic Set-up
Step 1:
Install the Wi-Fi Card
6
Step 2:
Install the Gateway Battery
(provides power should the electricity go out)
7
Step 3:
Install the Handset Batteries
8
Step 4:
Two Choices:
Charge the Handset with DC Adapter
9
OR
Charge the Handset Docked to the Gateway
10
Step 5:
Connect Cables
Connections Overview
11
Connect One or Two Computers with Ethernet Cables
12
Connect More than Two Computers with Ethernet Cables
13
Connect Telephone or Fax with Standard Analog Phone Line
13
Step 6:
Activate the Advanced Cable Gateway
14
Step 7:
Set-up Wireless Access for Your
Laptop, Wireless PC or Other Device
15
Step 8:
Become Familiar with the Handset Operation
16-18
Additional Options
Access and Change Gateway Advanced Settings
19-31
Customize Your Handset
32-35
Add Additional Handsets
(up to 5)
35
Order Additional Handsets
(up to 5 supported)
and Approved Rechargeable Handset Batteries -
Visit:
www.thomson-store.com
Page 12 / 54
6
3660181C
Wi-Fi Installation
Step 1: Install the Wi-Fi Card
The Advanced Cable Gateway is ready to support Wi-Fi and comes with a card. Follow these instructions for
installation:
Remove the protective cover over the Wi-Fi
slot located on the upper right hand side of the
Gateway.
Make certain that the front of the Wi-Fi card is
facing you.
Insert the Wi-Fi card in the slot as far as it will go
without forcing it.
Cover for Wi-Fi slot removed
WARNING
:
The Gateway
must
be unplugged from the wall socket
before
you attempt to install the Wi-Fi card.
FRONT of Wi-Fi card
(this side must face you
during insertion)
BACK
of Wi-Fi card
Slot for Wi-Fi with
cover removed
Page 13 / 54
7
3660181C
Charging and Batteries
Step 2: Install the Gateway Battery
Should the electricity go out, this will provide backup power to the Gateway:
Ensure the power cord is unplugged. Remove the
battery cover on the rear panel. There are two battery
compartments. One battery is included with the
Advanced Cable Gateway.
(To order additional compatible
batteries visit:
www.thomson-store.com
)
Push the slider up/down to allow for battery insertion.
Insert the battery into the compartment marked
Battery 1
”.
Readjust the slider to prevent the battery from moving
and replace the battery cover. Plug the power cord into
an electrical outlet that is not controlled by a wall switch
(this will assure that the unit has uninterrupted power).
The battery will fully charge within
5 hours
.
CAUTION
:
To reduce the risk of fire, personal injury or damage to the product, use only compatible rechargeable
batteries. The use of a non-rechargeable or incompatible batteries may damage the product and may be hazardous to
health.
Page 14 / 54
8
3660181C
Charging and Batteries
Step 3: Install the Handset Batteries
NOTE:
You must connect the handset battery before use.
NOTE: The RBRC seal on the battery used in your Thomson Inc. product
indicates that we are participating in a program to collect and recycle the
rechargeable battery (or batteries).
For more information go to the RBRC web site at www.rbrc.org
or call 1-800-8-BATTERY or contact a local recycling center.
CAUTION
:
To reduce the risk of fire or personal injury, use only the Thomson Inc. approved model GP 75AAAHC 1.2V
750mAh, rechargeable Nickel-metal Hydride AAA batteries, which are compatable with this unit.
• Slide the battery door off the back of the Handset.
• Insert the batteries
(included)
into the housing in the Handset being careful to align the + / - ends correctly
(refer to the graphics in the housing)
.
• Check that the screen lights up, then replace the cover.
• Wait for about 30 seconds to allow the system to start up.
• When your Handset is registered to its Gateway,
the screen displays the number “1” alongside the
(green - has signal)
symbol. The handset packaged
with your Gateway is “pre-registered” to the Gateway.
To register additional Handsets, please refer to page 35)
Battery Safety Precautions
• Do not burn, disassemble, mutilate, or puncture. Like other batteries of this type, toxic materials could be
released which can cause injury.
• To reduce the risk of fire or personal injury, use only the Nickel-metal Hydride battery listed in the
User’s Guide.
• Keep batteries out of the reach of children.
• Remove batteries if storing over 30 days.
Please refer to
www.thomson-store.com
to purchase approved batteries or for a list of approved batteries available
from other sources.
Attention
- special care should always be taken
with the loudspeaker - never allow anything to
poke through or pour into the holes. It is very
delicate.
Page 15 / 54
9
3660181C
Charging and Batteries
Changing the Battery
CAUTION
:
To reduce risk of personal injury, fire, or damage use only the S002CU0500020 power adaptor
listed in the user’s guide. This power adaptor is intended to be correctly orientated in a vertical or floor
mount position.
DC Adapter Charging Method
The DECT Handset dock can be stationed away from the
Advanced Cable Gateway.
In this situation, be certain that the DC adapter is
attached to both the dock and a power outlet.
Step 4: Charge the Handset (Two Ways)
Charge the Handset with the DC Adapter
The DECT Handset will charge when securely placed in the Handset Dock so long as the dock has power.
The dock can charge your handset while attached to the front of the Advanced Cable Gateway or by using the DC
adapter included with the Gateway.
DECT Handset
in its Dock
CAUTION
DC Adapter
Back of Dock
DC adapter connector
goes here
Once installation is complete, you should leave the phone on the charger for at least
5 hours
before using it in order to
maximize battery performance and life.

Rate

124.8 / 5 based on 304 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top