Page 6 / 72
Scroll up to view Page 1 - 5
Concurrent Dual Band Wireless N600 Gigabit Router
Chapter 2 Hardware
2.1
Panel Overview
Front Panel
Power LED:
A solid light indicates a proper connection to the power supply
while a blinking light indicates system is functioning correctly.
WPS LED:
A blinking light indicates router is performing WPS authentication
on a client device.
5G LED:
A solid light indicates wireless is active while a blinking light indicates
router is transmitting data wirelessly over 5GHz.
2.4G LED:
A solid light indicates wireless is active while a blinking light
indicates router is transmitting data wirelessly over 2.4 GHz.
LAN/1/2/3 LED:
A solid light indicates corresponding LAN port is correctly
connected while a blinking light indicates such port is transmitting data.
IPTV LED:
A solid light indicates corresponding IPTV port is correctly
connected while a blinking light indicates it is transmitting data.
WAN LED:
A solid light indicates the WAN port is correctly connected while a
blinking light indicates it is transmitting data.
USB LED:
A solid light indicates the USB port is correctly connected.
6
Page 7 / 72
Concurrent Dual Band Wireless N600 Gigabit Router
Back Panel
WAN:
Internet port
RJ-45
for connection to an Internet-enabled xDSL
Modem/Cable Modem or existing Ethernet.
IPTV
IPTV port for connection to a network set-top box. However such port can
function as a LAN port if IPTV STB port is not enabled.
LAN/1/2/3:
3 LAN ports
RJ-45
for connection to PC’s NIC or uplink to a hub,
switch or wireless AP.
WPS/Reset:
WPS button/Reset button: Pressing it for about 1 second enables WPS
encryption with a blinking WPS LED while Pressing it for about 7 seconds restores
the device to factory defaults.
2.2
Minimum System Requirements
I
nstalled Network Adapter
Internet Explorer 5.0 or higher
Broadband Internet Service (through xDSL/Cable Modem/Ethernet)
2.3
Hardware Installation
1. Connect one end of the included power adapter to the router and then plug
the other end into a wall outlet nearby. (Using a power adapter with a different
voltage rating than the one included with the router will cause damage to the
product.)
7
Page 8 / 72
Concurrent Dual Band Wireless N600 Gigabit Router
2
.
Connect one of the LAN ports on the Router to the NIC port on your PC using an
Ethernet cable.
3. Connect the Ethernet cable from Internet side to the WAN port on the Router.
8
Page 9 / 72
Concurrent Dual Band Wireless N600 Gigabit Router
Chapter 3 Login to Web Utility
The device’s default IP is
192.168.0.1. You can change it to accommodate your own
needs. Here in this manual, we use the default IP.
Connect you PC to the router and config your PC’s TCP/IP settings following
instructions in appendix 1 hereto. And then do as follows to run a Ping command
to test connectivity between your PC and the router.
±
1. Select “Start”—“Run” and enter “cmd”. Then press “Enter”.
±
Enter “ping
192.168.0.1” and press “Enter”. If you see the following screen, it
means the router is reachable on your PC. If you don’t get the following screen,
verify router’s power supply, Ethernet cable connections and your PC’s TCP/IP
settings.
9
Page 10 / 72
Concurrent Dual Band Wireless N600 Gigabit Router
Login to web utility
Launch a web browser on your PC and enter
as below. Then
press “Enter”.
Enter user name and password in corresponding fields on window below (Default
user name and password are respectively set to admin).
Note:
For security purpose, please change the default user name and password after you
logged in to web utility.
You will see the following interface if you entered a correct user name and a correct
password.
10
19216811.live