46

These fields are always enabled on the alternate model.

9.

Service mode

2G only, 2G preferred,

3G only, 3G preferred,

4G (LTE) only, 4G (LTE)

preferred or automatic.

Your network preference. If your local mobile network supports 2G,

3G and 4G (LTE) you can specify to which network you wish to

connect. E.g.: if you choose 2G, the router will connect to a 2G

network, so long as it is available, otherwise it will connect to a

network that provides better connectivity. If you select auto, then

the router will connect to the network that provides better

connectivity.

10.

Deny data

roaming

Enable/Disable

If enabled this function prevents the device from establishing mobile

data connection while not in home network.

11.

Use IPv4 only

Enable / Disable

If enabled this function makes the device to use only IPv4 settings

when connecting to operator.

Warning: If an invalid PIN number was entered (i.e. the entered PIN does not match the one that was used to

protect the SIM card), your SIM card will get blocked. To avoid such mishaps it is highly advised to use an unprotected

SIM. If you happen to insert a protected SIM and the PIN number is

incorrect, your card won’t get blocked immediately,

although after a couple of reboots OR configuration saves it will.

7.1.1.1.1

Passthrough mode

Using Passthrough Mode will disable most of the router capabilities!

DHCP mode: Static

Enter your computer MAC address (xx:xx:xx:xx:xx:xx) to MAC Address field and select Lease time (expire time for

lease addresses). Device, which MAC address will be entered, will get IP from GSM operator. Other connected devices to

the router LAN will get IP from router DHCP server, but these devices will not have internet access.

DHCP mode: Dynamic

Using Dynamic mode, device will get IP from GSM operator , which connect to the router firstly. Using

Passthrough in dynamic mode, the DHCP in LAN will be disabled.

DHCP mode: No DHCP

Using no DHCP mode, IP (also subnet, gateway and DNS) from GSM operator should be entered in device, which is

connected to the router LAN, manually. Using Passthrough in no DHCP mode, the DHCP in LAN will be disabled.

47

7.1.1.2

Mobile Data On Demand

Field name

Possible values

Explanation

1.

Enable

Enable/Disable

Mobile Data On Demand function enables you to keep mobile data connection

on only when it's in use

2.

No data

timeout(sec)

1-99999999

A mobile data connection will be terminated if no data is transferred during the

timeout period

7.1.1.3

Force LTE network

Field name

Possible

values

Explanation

1.

Enable

Enable/Disable

Enable/disable try to connect to LTE network every x seconds (used only if

service mode is set to 4G (LTE) preferred)

2.

Reregister

Enable/Disable

If this enabled, modem will be reregister before try to connect to LTE network

3.

Interval (sec)

180 - 3600

Time in seconds between tries to connect to LTE network. Range [180-3600]

48

7.1.2

SIM Management

Field name

Possible values

Explanation

1.

Primary SIM card

SIM 1 / SIM 2

SIM card that will be used in the system as a primary SIM card

2.

Enable automatic

switching

Enable/Disable

Automatically switch between primary and secondary SIM cards

based on the various rules and criterions defined below

3.

Check interval

1-3600

Check interval in seconds

4.

On weak signal

Enable/Disable

Perform a SIM card switch when a signal's strength drops below a

certain threshold

5.

On data limit*

Enable/Disable

Perform a SIM card switch when mobile data limit for your current

SIM card is exceeded

6.

On SMS limit*

Enable/Disable

Perform a SIM card switch when SMS limit for your current SIM card

is exceeded

7.

On roaming

Enable/Disable

Perform a SIM card switch when roaming is detected

8.

No network

Enable/Disable

Perform a SIM card switch when no operator is detected

9.

On network denied

Enable/Disable

Perform a SIM card switch when network is denied

10.

On data connection

fail

Enable/Disable

Perform a SIM card switch when data connection fails

* Your carrier's data usage accounting may differ. Teltonika is not liable should any accounting discrepancies occur.

49

7.1.3

Network Operators

7.1.3.1

Network Operators

This function lets you Scan, Select and enter manual Network Operator to which router should connect. Function

will provide great utility when router is in Roaming conditions. Operator is selected only for the active SIM card. In order

to specify operator for the other SIM card it must first be selected as primary SIM in “SIM Management”.

Note:

after clicking Scan for operators’ button

- You will lose current mobile connection!

For changing network operator

status have to be available. There is manual connection to network operator, you have to fill numeric name, and it’s

have to be available.

Field Name

Sample Value

Explanation

1.

SIM card in use

SIM 1 / SIM 2

Shows current SIM card’s in use

2.

Current operator

OMNITEL LT

Operator's name of the connected GSM network

50

7.1.3.2

Operator List

This function lets to create white list/black list based on operator’s code.

Field name

Possible values

Explanation

1.

Enable

Enable/Disable

Enable/disable operators blocking

2.

Mode

White list/Black list

White list - allows every operator on the list and blocks everything else.

Black list

–

block every operator on the list and allow everything else

3.

Name

Tele2 LT

Operator’s name

4.

Operator code

24603

Operator’s code

7.1.4

Mobile Data Limit

This function lets you limit maximum amount of data transferred on WAN interface in order to minimize

unwanted traffic costs.

7.1.4.1

Data Connection Limit Configuration

* Your carrier's data usage accounting may differ. Teltonika is not liable should any accounting discrepancies occur.

Field Name

Sample value

Explanation

1.

Enable data

connection limit

Enable/Disable

Disables mobile data when a limit for current period is reached

2.

Data limit* (MB)

200

Disable mobile data after limit value in MB is reached

3.

Period

Month/Week/Day

Period for which mobile data limiting should apply

4.

Start day/ Start hour

1

A starting time for mobile data limiting period