Telewell TW-EAV510v2 Router Manual PDF (Setup & Configuration Guide)

Page 141 / 169 Scroll up to view Page 136 - 140

141

The above is the commonly setting for L2TP Server, set as you like for authentication and encryption.

The settings in Client side should be in accordance with settings in Server side.

Then account the L2TP Account.

Client Side: Branch Office

The client user can set up a tunnel connecting to the PPTP server, and can also set the tunnel as the

default route for all outgoing traffic.

Note:

users can see the “Default Gateway” item in the bar, and user can check to select the tunnel as

the default gateway (default route) for traffic. If selected, all outgoing traffic will be forwarded to this

tunnel and routed to the next hop.

Page 142 / 169

142

GRE

Generic Routing Encapsulation (GRE) is a tunneling protocol that can encapsulate a wide variety of

network layer protocol packets inside virtual point-to-point links over an Internet Protocol (IP) network.

And the common use can be GRE over IPSec.

Note

: up to 8 tunnels can be added, but only 4 can be activated.

Name

: User-defined identification.

WAN Interface

: Select the exact WAN interface configured for the tunnel as the source tunnel IP.

Select Default to use the now-working WAN interface for the tunnel.

Local Tunnel Virtual IP

: Please input the virtual IP for the local tunnel.

Local Netmask

: Input the netmask for the local tunnel.

Remote Tunnel Virtual IP

: Please input the virtual destination IP for tunnel.

Remote Gateway IP

: Set the destination IP for the tunnel.

Remote Network

: Select the peer topology, Single address (client) or Subnet.

IP Address

: Set the IP address if the peer is a client. If the peer is a subnet, please enter the IP and

netmask.

Enable Keepalive

: Normally, the tunnel interface is always up. Enable keepalive to determine when

the tunnel interface is to be closed. The local router sends keepalive packets to the peer router, if

keepalive response is not received from peer router within the allowed time (‘retry time’ multiply

‘interval’, based on default settings, the time interval can be 30 seconds), the local router will shut up

its tunnel interface.

Keepalive Retry Times

: Set the keepalive retry times, default is 10.

Keepalive Interval

: Set the keepalive Interval, unit in seconds. Default is 3 seconds.

Page 143 / 169

143

Advanced Setup

There are sub-items within the System section: Routing, DNS, Static ARP, UPnP, Certificate,

Multicast, Management, and Diagnostics.

Routing

Default Gateway

WAN port

: Select the port this gateway applies to.

To set Default Gateway and Available Routed WAN Interface. This interfaces are the ones you have

set in WAN section, here select the one you want to be the default gateway by moving the interface

via

or

.

And select a Default IPv6 Gateway from the drop-down menu.

Note

: Only one default gateway interface will be used according to the priority with the first being the

highest and the last one the lowest priority if the WAN interface is connected.

Page 144 / 169

144

Static Route

With static route feature, you can control the routing of all the traffic across your network. With each

routing rule created, you can specifically assign the destination where the traffic will be routed.

Above is the static route listing table, click Add to create static routing.

IP Version

: Select the IP version, IPv4 or IPv6.

Destination IP Address / Prefix Length

: Enter the destination IP address and the prefix length. For

IPv4, the prefix length means the number of ‘1’ in the submask, it is another mode of presenting

submask. One IPv4 address,192.168.1.0/24, submask is 255.255.255.0. While in IPv6, IPv6 address

composes of two parts, thus, the prefix and the interface ID, the prefix is like the net ID in IPv4, and

the interface ID is like the host ID in IPv4. The prefix length is to identify the net ID in the address. One

IPv6 address, 3FFE:FFFF:0:CD30:0:0:0:0 / 64, the prefix is

3FFE:FFFF:0:CD3.

Interface: Select an interface this route associated.

Gateway IP Address

: Enter the gateway IP address.

Metric

: Metric is a policy for router to commit router, to determine the optimal route. Enter one number

greater than or equal to 0.

Click Apply to apply this route and it will be listed in the route listing table.

ln listing table you can remove the one you don't want by checking the checking box and press

Remove

button.

Policy Routing

Here users can set a route for the host (source IP) in a LAN interface to access outside through a

specified Default Gateway or a WAN interface.

The following is the policy Routing listing table.

Page 145 / 169

145

Click Add to create a policy route.

Policy Name

: User-defined name. Physical LAN Port: Select the LAN port. Source IP: Enter the Host

Source IP.

Interface

: Select the WAN interface which you want the Source IP to access outside through.

Default Gateway

: Enter the default gateway which you want the Source IP to access outside through.

Click Apply to apply your settings. And the item will be listed in the policy Routing listing table. Here if

you want to remove the route, check the remove checkbox and press Remove to delete it.

RIP

RIP, Router Information Protocol, is a simple Interior Gateway Protocol (IGP). RIP has two versions,

RIP-1 and RIP-2.

Interface

: the interface the rule applies to.

Version

: select the RIP version, there are two versions, RIP-1 and RIP-2.

Operation

: RIP has two operation mode.

i

Passive: only receive the routing information broadcasted by other routers and modifies its

routing table according to the received information.

i

Active: working in this mode, the router sends and receives RIP routing information and

modifies routing table according to the received information.

Enable

: check the checkbox to enable RIP rule for the interface.

Rate

Popular Telewell Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share