1. Home
    2. /
  2. Manuals
    3. /
  3. Telewell
    4. /
  4. TW-EA1000
    5. /
  5. 5
Page 21 / 37 Scroll up to view Page 16 - 20
TW-EA1000 Wireless ADSL Firewall Router
17
If you are going to configure more parameters, the LOGIN IN window will prompt for a
username and password. The default username and password are admin and admin.. If you have
set a password, enter that and click
“OK”
to continue.
At the configuration homepage, the left navigation pane where bookmarks are provided links
you directly to the desired setup page, including
Status
(status and PPTP status),
Quick Start
,
Configuration
(LAN, WAN, System, VPN, Virtual Server, Advanced) and
Save Config to
FLASH
functions. Besides, it provides user interface in multi-languages.
Click on the desired item to expand the page in the main navigation pane.
3.4.1 STATUS
In this screen as the above figure, it contains many items including device H/W and S/W
information, LAN, WAN, Port status and all defined interfaces. Gives you a quick view to know
the TW-EA1000’s current status. When you click the Status -> PPTP status, the status of PPTP
connection will be shown.
3.4.2
Quick Start
If you use this device to access the Internet through the ISP, this web page is enough for you to
configure this router and access the Internet without a problem. Please check Chapter 3.3, then
enter the proper values into this web page, click the APPLY button and then Save Config to
Page 22 / 37
Chapter 3 Configuration
18
FLASH in the left panel. After the router reboot, you may check the Status web page to check
whether the router is connected to the ISP or not. In most cases, you can access the Internet
immediately, if you do not use a Wireless LAN client card. If not please refer to the sections
below for more information.
3.4.3 Configuration
When you click this item, you get following sub-items to configure the Router.
LAN, WAN, System, VPN, Virtual Server and Advanced
These functions are described below in the following sections.
Page 23 / 37
TW-EA1000 Wireless ADSL Firewall Router
19
3.4.3.1 LAN
There are three items under the LAN section, Ethernet, Wireless and DHCP Server. When you
click
Ethernet
, you will get the following picture as below.
It supports two Ethernet IP addresses in the LAN. With this function, the Router can support two
different LAN subnets to access the Internet at the same time. Usually, there is only one subnet
in LAN, there is no need to configure a Secondary IP address. The 192.168.0.254 is the default
IP address for this Router. The Advanced Options will allow you to configure the routing
protocol version1 or version 2 in receiving and sending direction.
When you click
Wireless
, you will get the following figure.
ESSID:
Enter the unique ID given to the Access Point (AP), which is built in the wireless
broadband firewall gateway. To connect to this device, your wireless clients must have the same
ESSID as the device.
Reguration_Domain:
There are five Reguration_Domain for you to choose, including
N.America
,
Europe
,
France
, and
Spain
.
The Channel ID will be different based on this
setting.
Channel ID:
Select the ID of channel you would like to use.
Default Tx Key:
Select the encryption key ID, please refer to
Key (0-3)
below.
Page 24 / 37
Chapter 3 Configuration
20
Passphrase:
This is used to generate WEP keys automatically by input string and
pre-defined algorithm in WEP64 or WEP128. You can input same string in both AP
and Client card to generate same WEP keys. Please note you do not have to key in
Key (0-3)
as
below when
Passphrase
is enabled.
WEP Encryption:
To prevent unauthorized wireless stations from accessing data transmitted
over the network, the wireless broadband firewall gateway offers highly secure data encryption,
known as WEP. If you require high security in transmission, there are two alternatives to select
from, WEP 40 and WEP 128.
Key (0-3):
Enter the key to encrypt wireless data. To allow encrypted data transmission, the
WEP Encryption Key values on all wireless stations must be the same as the device. There are
four keys for your selection. The input format is in HEX style, 5 and 13 HEX codes are required
for WEP64 and WEP128 respectively, the separator is “-“. Take WEP64 case for example, 11-
22-33-44-55 is a valid key, 1122334455 is invalid instead.
Hide_SSID:
When enabled, the Wireless AP is invisible from the site-surveying by Wireless
clients. The wireless clients still can associate with this Wireless AP if entered with the same
ESSID value.
Reset:
Reset the Wireless AP function.
When you click
DHCP Server
, you will get the following figure. You can disable or enable the
Server or enable the DHCP relay functions.
If you check
Disabled
and click
Next,
then click
Apply.
The DHCP server function is disabled.
Each PC in the LAN should assign a fixed IP address and set the PC’s gateway to the Router.
If you check
DHCP Server
and click
Next
, you can configure parameters of the DHCP server
including the IP pool (starting IP address and ending IP address), leased time for each assigned
IP address, DNS IP address, Gateway IP address. Those messages are sent to the DHCP client
when it requests an IP address from the DHCP server. Click
Apply
to enable this function. If
you check “Use Router as a DNS Server”, the Router will find the IP address automatically from
the outside network and forward it back to the requesting PC in the LAN.
Page 25 / 37
TW-EA1000 Wireless ADSL Firewall Router
21
If you check
DHCP Relay Agent
and click
Next
, you will have to enter the IP address of the
DHCP server which will assign an IP address back to the DHCP client in the LAN. Click
Apply
to enable this function.
DHCP Server
~
Disable:
Check to disable the TW-EA1000 from distributing IP Addresses to the local
network.
If you check this selection, remember to specify a static IP address, subnet Mask, and DNS
setting for each of your local computers. Be careful NOT to assign the same IP address to
different computers.
~
Enable:
Check to enable the TW-EA1000 to distribute IP Addresses, subnet mask and DNS
setting to computers. Hence, the following fields will be activated.
Starting IP Address:
Enter the starting address of this local IP network address pool. The pool
is a piece of continuous IP address segment. The default value is
192.168.0.100
.
Number of DHCP users:
Enter the maximum number of computers that you want the DHCP
server to assign IP addresses to. The default value is
100
.
With this case, the DHCP pool is from 192.168.0.100 to 192.168.0.199. Therefore, the local
computer will randomly pick at an IP address within this range.

Rate

4.5 / 5 based on 2 votes.

Popular Telewell Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top