1. Home
    2. /
  2. Manuals
    3. /
  3. Technicolor
    4. /
  4. TG799vn-v2
    5. /
  5. 13
Page 61 / 128 Scroll up to view Page 56 - 60
53
6 TELEPHONY
DMS-CTC-20110713-0016 v2.0
6.1.1
Connecting a DECT Phone to Your MediaAccess
Gateway
Introduction
The MediaAccess Gateway is equipped with a DECT base station allowing you to connect up to five DECT phones.
Before you can start using your DECT phone, you first have to pair it with your MediaAccess Gateway.
Procedure
Proceed as follows:
1
Put the MediaAccess Gateway in pairing mode. You can do either of the following:
Press the
DECT
button on the MediaAccess Gateway until the DECT LED on the front panel starts flashing.
Via the
MediaAccess Gateway GUI
.
1
On the
Toolbox
menu, click
Telephony
.
2
Under
Pick a task
, click
DECT pairing
.
2
Put your DECT phone in pairing mode.
Consult your DECT phone’s user documentation to register your DECT phone.
3
Your DECT phone prompts you that If the registration is successful, the message “Registered to base x” appears on the
screen of your Technicolor DECT phone.
Page 62 / 128
54
6 TELEPHONY
DMS-CTC-20110713-0016 v2.0
6.1.2
Connection to the Traditional Telephone Network
Combining VoIP with the traditional telephone network
Some service providers use the traditional telephone network (PSTN) as a backup solution for your VoIP connection. This
way, you can still make calls over the traditional network if the VoIP service is down (for example, your MediaAccess
Gateway is powered off).
Applicability
If your MediaAccess Gateway:
Has an integrated filter, no additional connections are needed.
The DSL port must be directly connected to your telephone outlet. Do not put any filter or splitter between them!
Does not have an integrated filter, check if your MediaAccess Gateway has a
PSTN
port on the back panel (for more
information, see
“PSTN Port (optional)” on page 10
). If your MediaAccess Gateway has:
A
PSTN
port:
Connect the
PSTN
port to the
Phone
output of your filter or splitter.
No
PSTN
port, no connections are needed.
This is a VoIP-only variant. All calls passing through the MediaAccess Gateway will be done via VoIP.
Be aware that, if you are not connected to the traditional telephone network, emergency calls will not be possible
when your Internet connection is down or your MediaAccess Gateway is powered off.
How do I know if my MediaAccess Gateway has an integrated filter?
Check if the product name printed on the label of your MediaAccess Gateway ends with “wIF” (
w
ith
I
ntegrated
F
ilter). If this suffix is not present, then your MediaAccess Gateway does not have an
integrated filter.
Page 63 / 128
55
6 TELEPHONY
DMS-CTC-20110713-0016 v2.0
6.1.3
Configuring the MediaAccess Gateway VoIP Service
Introduction
If your VoIP service has not been configured yet, follow the instructions in this section.
How can I check if the VoIP service has already been configured?
If the
Phone
LED is:
Solid or blinking green then the VoIP service is configured correctly. No configuration is needed.
Off then telephony service is not configured (yet). Follow the instructions below.
Requirements
Your Internet connection must be up and running before you can configure Internet telephony.
Configuring the VoIP settings
Proceed as follows:
1
Enter the proxy and registrar settings
.
2
Enter your VoIP account settings
.
Enter the proxy and registrar settings
Proceed as follows:
1
Browse to the MediaAccess Gateway GUI.
For more information, see
“Accessing the MediaAccess Gateway GUI” on page 37
.
2
On the
Toolbox
menu, click
Telephony
.
3
In the
Navigation bar
, click
Expert configure
.
4
Complete the following fields based on the settings provided by your VoIP provider:
Proxy:
Type the URL (for example: sip.provider.com) or IP address of the proxy.
Registrar:
Type the URL (for example: sip.provider.com) or IP address of the registrar.
Registrar Port
and
Proxy Port
.
In most cases the default port (5060) will be used. Only change these values if your provider is using other port
numbers.
5
Click
Apply
.
Enter your VoIP account settings
Proceed as follows:
1
In the
Navigation bar
, click
Configure
.
2
Under
Service Configuration
, select
Enable Telephony
.
3
Under
Telephone Numbers
, complete the following fields:
SIP URI
:
The Uniform Resource Identifier (URI) of your SIP account (for example: 035051979, john.doe,...). This is the
telephone number that people have to dial to call you.
Username:
The user name of your VoIP account (for example: 035051979, john.doe,...).
Page 64 / 128
56
6 TELEPHONY
DMS-CTC-20110713-0016 v2.0
Password:
The password of your VoIP account.
Displayname:
The name that you want people to see on the display of their phone when you are calling.
Abbreviated number:
An internal number to call the phones associated with this VoIP account.
Port:
The phone port that you want to associate with this VoIP account. select
All
to use this VoIP account for all connected phone (fixed + DECT).
All DECT
to use this VoIP account for all connected DECT phones.
DECT 1/2/3/4/5
to use this VoIP account for one specific DECT phone. You can find the number of your DECT
phone its display.
Phone 1/2
to use this VoIP account for the phone connected to the
Phone 1/2
port of your MediaAccess Gateway.
4
Click
Apply
.
Verifying Telephone Connectivity
Proceed as follows to verify the voice connection:
1
Make sure the MediaAccess Gateway is turned on.
2
Make sure the Internet telephony service is enabled and configured. The
Phone/DECT
LED must be solid green.
3
Pick up your phone, wait for the dialling tone, and dial the number.
Your VoIP provider may not support this feature.
Page 65 / 128
57
6 TELEPHONY
DMS-CTC-20110713-0016 v2.0
6.2
Address Book
Introduction
The
Address Book
page allows you to:
Store your contacts on the
MediaAccess Gateway GUI
.
Initiate a call or send a message by clicking the phone number or e-mail address in the contact details.
Everyone with access to the MediaAccess Gateway GUI can view and use the address book.
Accessing the Address Book page
Proceed as follows:
1
Browse to the MediaAccess Gateway GUI.
For more information, see
“Accessing the MediaAccess Gateway GUI” on page 37
.
2
On the
Toolbox
menu, click
Address Book.
3
The
Address Book
page appears.
For each contact, you can provide the following information:
Business
: to make a call to the contact’s business telephone number
Home
: to make a call to the contacts home telephone number
Mobile
: to make a call to the contact’s mobile telephone number
Other or SIP uri
: to make a call to the contact’s VoIP telephone number
E-mail
to send an E-mail message to the contact with your e-mail client.
Managing contacts
All information provided per contact is optional except for the last and first name. The information can be updated or
completed at any time.
Click...
To...
Add
Add a contact
Edit
Edit a contact
Delete
Delete a contact

Rate

4.5 / 5 based on 2 votes.

Popular Technicolor Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top