1. Home
    2. /
  2. Manuals
    3. /
  3. Technicolor
    4. /
  4. TC7210-dNZ
    5. /
  5. 14
Page 66 / 91 Scroll up to view Page 61 - 65
Page
66
/
91
3.
Access Control
This page allows you to control device that can connect to the AP and list all connected clients. Control is
made by Mac Address.
Fig. 2-47 Gateway\Wireless\Access Control
Administration Web Page Access:
This field let you decide if a PC connected over Wi-Fi to the
Gateway can have access to the Gateway Web Pages.
MAC Restrict Mode:
Click
Disabled
to welcome all of the clients on the network; select
Allow
to
permit only the clients on the list to access the cable modem; or choose
Deny
to prevent the clients
on the list to access this device.
MAC Address:
Your Gateway identifies wireless PCs by their Wireless MAC Address. This
address consists of a string of 6 pairs of numbers 0-9 and letters A-F, such as 00 90 4B F0 FF 50. It
is usually printed on the Wireless card of the device (e.g. the PCMCIA card in a laptop).
Enter the MAC addresses of the connected clients into the fields, and then click Apply to add them
to the list for access control.
Apply:
After proper configuration, click Apply to invoke the settings.
Connected Clients:
The information of currently connected clients will be displayed here.
Page 67 / 91
Page
67
/
91
4.
Advanced
This page allows you to configure some advanced settings. The factory default values should provide
good results in most
cases. We don’t recommend you change these settings unless you have technical
knowledge of 802.11 wireless technology.
For expert users, details of all settings on this web page are provided below.
Fig. 2-48 Gateway\Wireless\Advanced
54
TM
Mode:
Except Auto mode, there are three modes for you choose, please check the specification
of your wireless card and choose a proper setting.
Xpress
TM
Technology:
When Xpress is turned on, aggregate throughput (the sum of the individual
throughput speeds of each client on the network) can improve by up to 27% in 802.11g-only
networks, and up to 75% in mixed networks comprised of 802.11g and 802.11b standard equipment.
802.11n Protection:
This method provides 802.11g and 802.11b devices can co-exist in the same
network without “speaking” at the same time.
Default is
“
Auto
”
.
Short Guard Interval:
To reduce complexity, manufacturers typically only implement a short
guard interval as a final rate adaptation step when the device is running at its highest data rate.
Default is
“
Auto
”
.
Basic Rate Set:
The rates that for all clients want to associate with. Choose
“
Default
”
or
“
All
”
for
the
802.11a/b/g/n/ac
.
Page 68 / 91
Page
68
/
91
Multicast Rate:
The baseline levels that wireless device able to deliver in order to connect to the
wireless voice gateway. Lower multicast rates mean weaker, farther signals are allowed to
connection. Higher multicast rates mean that only close, strong signals are allowed.
NPHY Rate:
Set the Physical Layer rate. The rate always set
“
Use Legacy Rate
”
.
Rate:
It decides the speed of data transmission. There are several rates provided here for you to
choose. Choose any one of it according to your needs by using the drop-down menu.
Beacon Interval:
Set the period of beacon transmissions to allow mobile stations to locate and
identify a BSS. The measure unit is “time units” (TU) of 1024 microseconds. (Value range:
1~65535)
DTIM Interval:
The value you set here is used to inform mobile stations when multicast frames that
have been buffered at the Wireless Voice Gateway will be delivered and how often that delivery
occurs. (Value range: 1~255)
Fragmentation Threshold:
Set the number of the fragmenting frames to make the data to be
delivered without errors induced by the interference. Frames longer than the value you set here are
fragmented before the initial transmission into fragments no longer than the value of the threshold.
(Value range: 256~ 2346)
RTS Threshold:
Set the value for sending a request to the destination. All the frames of a length
greater than the threshold that you set here will be sent with the four-way frame exchange. And, a
length less than or equal to the value that you set will not be proceeded by RTS. (Value range: 0~
2347)
Page 69 / 91
Page
69
/
91
5.
Bridging
The Bridging page provides a location where settings can be adjusted related to the WDS (
Wireless
Distribution System)
feature.
WDS is a system that enables the interconnection of access points wirelessly. It may also be referred to as
repeater mode because it appears to bridge and accept wireless clients at the same time (unlike traditional
bridging).
The wireless gateway can be placed in a mode that allows the gateway to communicate with other
“extender” wireless access points either exclusively or mixed with communications to local PCs. Use this
page to designate the Remote Bridges the gateway is allowed to communicate with, and to select the
Wireless Bridging mode.
Fig. 2-49 Gateway\Wireless\Bridging
Wireless Bridging:
Choose
“
Disabled
”
to shutdown this function; select Enabled to turn on the
function of WDS.
Remote Bridges:
Enter the MAC Addresses of the remote Bridges to relay the signals for each
other.
Apply:
After proper configuration, click Apply to invoke the settings.
Page 70 / 91
Page
70
/
91
6. 802.11 Wi-Fi Multimedia:
Wi-Fi Multimedia (WMM) is a component of the IEEE 802.11e wireless LAN standard for quality of
service (QoS). The QoS assigns priority to the selected network traffic and prevents packet collisions and
delays thus improving VoIP calls and watching video over WLANs.
Fig.2-50 Gateway\Wireless\WMM
Enable WMM:
This field allows you to enable WMM to improve multimedia transmission.
Enable WMM No-Acknowledgement
: This field allows you to enable WMM No-
Acknowledgement.

Rate

4.5 / 5 based on 2 votes.

Popular Technicolor Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top