Page 96 / 139
Scroll up to view Page 91 - 95
85
Scan Area Size:
You can select from the following list of preset scan sizes. Please note that you can
also dynamically adjust the scan size by clicking and dragging the dotted box that
appears on the image on the right.
•
Full Bed - Scans the entire bed of the scanner
•
Letter - This selection will scan an 8.5x11 portion of your scanner bed
•
Executive - This selection will scan an area roughly 7.5x10 on the scanner
bed
•
A4 - This selection will scan an area roughly 8x11
•
Custom - This selection allows you to choose a size you specifically want
•
Offset:
Enter an offset in inches or millimeters.
Resolution:
Select the resolution from Low to Highest. The highest resolution is recommended
for photo's that will be enlarged or just images that are going to be cropped. The
lowest setting should be used for images that are not quality dependant, or even to
send sketches over email.
Copy Color:
Select color or black & white for the output of your scan.
File Format:
Select from either JPEG or PDF format. Both are very popular and can be viewed on
many computers. Please note that you will need at least Adobe Reader to view files
scanned into PDF format.
Scan Button:
Once all your settings are set, click the Scan button to scan your document or
picture!
Page 97 / 139
86
Status
The Status tab provides the following configuration options:
Device Info, Wireless, Routing,
Logs, Statistics and Active Sessions.
Status_Device info
All of your Internet and network connection details are displayed on the Device Info page.
The firmware version is also displayed here.
Some browsers have limitations that make it impossible to update the WAN
status display when the status changes. Some browsers require that you refresh
the display to obtain updated status. Some browsers report an error condition
when trying to obtain WAN status.
Page 98 / 139
87
Depending on the type of WAN connection, you can take one of the following sets of
actions:
DHCP Connection
Clicking the
DHCP Release
button unassigns the router's IP address. The router will
not respond to IP messages from the WAN side until you click the
DHCP Renew
button or power-up the router again. Clicking the
DHCP Renew
button causes the
router to request a new IP address from the ISP's server.
Page 99 / 139
88
PPPoE, PPTP, L2TP Connection
Depending on whether the WAN connection is currently established, you can click
either the
Connect
to attempt to establish the WAN connection or the
Disconnect
to
break the WAN connection.
BigPond Connection
Depending on whether you are currently logged in to BigPond, you can click either
the
BigPond Login
to attempt to establish the WAN connection or the
BigPond
Logout
to break the WAN connection.
LAN Computers
This area of the screen continually updates to show all DHCP enabled computers
and devices connected to the LAN side of your router. The detection "range" is
limited to the address range as configured in DHCP Server. Computers that have an
address outside of this range will not show. If the DHCP Client (i.e. a computer
configured to "Automatically obtain an address") supplies a Host Name then that will
also be shown. Any computer or device that has a static IP address that lies within
the detection "range" may show, however its host name will not.
IGMP Multicast memberships
If IGMP is enabled, this area of the screen show all multicast groups of which any
LAN devices are members.
Page 100 / 139
89
Status_Wireless
The wireless section allows you to view the wireless clients that are connected to your
wireless router.
MAC Address
The Ethernet ID (MAC address) of the wireless client.
IP Address
The LAN-side IP address of the client.
Mode
The transmission standard being used by the client. Values are 11a, 11b, or 11g for
802.11a, 802.11b, or 802.11g respectively.
Rate
The actual transmission rate of the client in megabits per second.
Signal
This is a relative measure of signal quality. The value is expressed as a percentage
of theoretical best quality. Signal quality can be reduced by distance, by interference
from other radio-frequency sources (such as cordless telephones or neighboring
wireless networks), and by obstacles between the router and the wireless device.