1. Home
    2. /
  2. Manuals
    3. /
  3. SMC
    4. /
  4. SMCWBR14S-N3
    5. /
  5. 18
Page 86 / 106 Scroll up to view Page 81 - 85
System Configuration
5-52
5
DHCP Clients
Lists information about associated DHCP clients.
Figure 5-43.
DHCP Client List (Gateway Mode)
•
MAC Address
– The MAC address of the DHCP client.
•
IP Address
– The IP address of the DHCP client.
•
Expires in
– The time after which the connection will expire and the DHCP client
must request a new IP address.
System Log
The wireless AP/Router supports a logging process that controls error messages
saved to memory or sent to a Syslog server. The logged messages serve as a
valuable tool for isolating wireless AP/Router and network problems. The System
Log page displays the latest messages logged in chronological order, from the
newest to the oldest. Log messages saved in the wireless AP/Router’s memory are
erased when the device is rebooted.
Figure 5-44.
System Logs
•
Refresh
– Sends a request to add the latest entries to the System Log Table.
•
Clear
– Removes the current system log messages from the System Log Table.
Page 87 / 106
Administration Settings
5-53
5
Reboot
•
Reboot
– Click the button to reboot the wireless AP/Router.
Figure 5-45.
System Reboot
Page 88 / 106
System Configuration
5-54
5
Page 89 / 106
A-1
Appendix A: Troubleshooting
Check the following items before you contact local Technical Support.
1.
If wireless clients cannot access the network, check the following:
•
Be sure the access point and the wireless clients are configured with the same
Service Set ID (SSID).
•
If authentication or encryption are enabled, ensure that the wireless clients are
properly configured with the appropriate authentication or encryption keys.
2.
If the wireless AP/Router cannot be configured using a web browser:
•
Be sure to have configured the access point with a valid IP address, subnet
mask and default gateway.
•
If you are connecting to the wireless AP/Router through the wired Ethernet
interface, check the network cabling between the management station and the
wireless AP/Router. If you are connecting to wireless AP/Router from a
wireless client, ensure that you have a valid connection to the wireless AP/
Router.
3.
If you forgot or lost the password:
•
Set the wireless AP/Router to its default configuration by pressing the reset
button on the bottom panel for 5 seconds or more. Connect to the web
management interface using the default IP address 192.168.2.1. Then set up
a new user name and password to access the management interface.
4.
If all other recovery measure fail, and the wireless AP/Router is still not
functioning properly, take any of these steps:
•
Reset the wireless AP/Router’s hardware using the web interface or through
a power reset.
•
Reset the wireless AP/Router to its default configuration by pressing the reset
button on the back panel for 5 seconds or more. Connect to the web
management interface using the default IP address 192.168.2.1, then setup a
user name and password.
Page 90 / 106
Troubleshooting
A-2
A
Diagnosing LED Indicators
Troubleshooting Chart
Symptom
Action
POWER LED is Off
•
The AC power adapter may be disconnected. Check connections
between the wireless AP/Router, the power adapter, and the wall
outlet.
WLAN LED is Off
•
The wireless AP/Router’s radio has been disabled through it’s web
management interface. Access the management interface using a web
browser to enable the radio.
LAN/WAN LED is Off
(when port connected)
•
Verify that the wireless AP/Router and attached device are powered
on.
•
Be sure the cable is plugged into both the wireless AP/Router and
corresponding device.
•
Verify that the proper cable type is used and its length does not exceed
specified limits.
•
Check the cable connections for possible defects. Replace the
defective cable if necessary.

Rate

124.8 / 5 based on 304 votes.

Popular SMC Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top