1. Home
    2. /
  2. Manuals
    3. /
  3. SMC
    4. /
  4. D3G0804W
    5. /
  5. 11
Page 51 / 113 Scroll up to view Page 46 - 50
40
D3G0804W User Manual
Table 8. WPS Page Options
Option
Description
WPS Enable/Disable
WPS
Enables or disables WPS. If you click Enabled, complete the remaining fields on the page.
Security
A read-only field that shows the Gateway’s security settings.
Encryption
A read-only field that shows the Gateway’s encryption settings.
AP PIN
A read-only field that shows the Access Point’s personal identification number.
Configured Status
A read-only field that shows the configuration status of the Gateway. Clicking RESET TO UNCONFIGURED resets the
WPS settings.
Add Wireless Client (WPS)
Connection Options
Select the method used to make the Wi-Fi Protected Setup (WPS) connection between wireless devices and the
Gateway. Choices are:
•
Push Button = select this option to use the WPS button on the front panel of the Gateway and the wireless device to
make the connection.
•
Pin Number = a PIN is a unique number that can be used to add a client to an existing network or to create a new
network. Select this option to enter an 8-digit PIN to configure WPS. Then, enter the same 8-digit PIN in both the
Wireless Client’s PIN field and at the wireless client to make the wireless connection.
Wireless Client’s PIN
If Connection Options is set to Pin Number, enter the PIN used with the wireless client to make the wireless connection.
This option does not appear if Connection Options is set to Push Button.
PAIR Button
If Connection Options is set to Push Button, click this button and push the WPS button on the wireless client to create the
wireless connection. The wireless connection is made within two minutes. You can also press the WPS button on the front
panel of this Gateway to initiate WPS instead of clicking the PAIR button.
CANCEL Button
Click this button to discard your changes on this page and return to the previous page settings.
WPS Lock Status
lock_status
A read-only field that shows the Gateway’s lock status. WPS is a method for setting up a new wireless Gateway using a
push button or PIN.WPS has a vulnerability that makes a PIN susceptible to brute force attempts. The Gateway protects
itself after several failed attempts to authenticate via a PIN by entering a lock state. During the lock state, all WPS
attempts using the Gateway PIN will not work. While the Gateway is in a lock state, users can still use the WPS button
method to connect to the wireless network. Clicking UNLOCK returns the Gateway from the lock state.
Page 52 / 113
41
D3G0804W User Manual
WAN Page
Path:
Connection > WAN
The WAN page shows information about the Wide Area Network, cable modem, and downstream and
upstream bonding values. This information is useful when contacting Customer Center or
troubleshooting technical problems.
Note:
This page is also available from the Status page by clicking the
VIEW
button in the
WAN
IP Network
area.
Figure 22. WAN Page
Page 53 / 113
42
D3G0804W User Manual
Table 9. WAN Page Options
Option
Description
WAN
Internet
A read-only field that shows the Internet connection status.
System Uptime
A read-only field that shows the system uptime counting from its bootup.
WAN IP Address
A read-only field that shows the WAN IP v4 address obtained from the service provider.
WAN IPv6 Address
A read-only field that shows the WAN IP v6 address obtained from the service provider.
Prefix
A read-only field that shows the IPv6 prefix length.
DHCP Client
A read-only field that shows the DHCP Client function is enable or disable.
DHCP Expiry Time
A read-only field that shows the expired time currently left of DHCP client. Once the time expires, the configuration
might stop working.
CM MAC
A read-only field that shows the MAC address of the CM.
WAN MAC
A read-only field that shows the MAC address of the Gateway’s WAN interface.
Cable Modem
Read-only fields that show technical information related to your cable modem, such as the hardware version, vendor, and boot and core versions.
Downstream Channel Bonding Value
Downstream channel bonding lets the Gateway receive downstream traffic on multiple downstream channels. These read-only fields show the
downstream channel bonding values, such as channel ID, frequency, signal-to-noise ratio, power, and modulation.
Upstream Channel Bonding Value
Upstream channel bonding is a way to increase upstream bandwidth by transmitting data on multiple upstream channels simultaneously. These read-only
fields show the upstream channel bonding values, such as channel ID, frequency, power level, range backoff start and end, and modulation.
Page 54 / 113
43
D3G0804W User Manual
Firewall Settings Page
Path:
Gateway > Firewall
The Gateway includes a built-in firewall whose security level can be selected using the Firewall Settings
page. Security levels range from minimum (low security) to maximum (high security).
Figure 23. Firewall Settings Page
To select a security level, click the radio button next to the level and then click the
SAVE SETTINGS
button. To see the protection associated with a security level, click the name of the security level to
expand the security level. If you click the words
Maximum Security Level
(not the radio button next to
the words), for example, the maximum security area on the page expands as shown in Figure 24.
Page 55 / 113
44
D3G0804W User Manual
Figure 24. Example of Expanding Maximum Security
If you click the words
Custom Security
option (not the radio button next to the words), the options in
Figure 25 appear. You can then choose the desired options to customize security settings to suit your
requirements. After checking the desired options, click the radio button to select custom security.
Figure 25. Example of Expanding Custom Security
Clicking the underlined
security level…
…displays this expanded list
of items that are allowed or
blocked.

Rate

4 / 5 based on 1 vote.

Popular SMC Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top