SmartRG™ Resi

dential Gateways

P a g e

| 46

C o n f i d e n t i a l

S m a r t R G © 2 0 1 2

To configure the SmartRG’s QoS feature:

1.

Ensure the layer 2 WAN interface “Enable Quality of Service” check box is checked as

detailed in the Layer 2 Interface configuration sections.

2.

Select

Advanced Setup -> Quality of Service -> QoS Config

Figure 37 Enable the SmartRG's QoS Processing

3.

Check “Enable QoS”, set the “Default DSCP Mark” to “No Change(

-

1)” and click

Apply/Save.

4.

Create the VoIP queue by selecting

Advanced Setup -> Quality of Service -> QoS Queue

Config

and click Add.

Figure 38 QoS: VoIP Queue Configuration

Configuring Your SmartRG™

- Common Use Cases

S m a r t R G © 2 0 1 2

C o n f i d e n t i a l

P

a

g

e

| 47

5.

Name, enable and select the WAN interface to be fed by this queue.

IMPORTANT

NOTE

Select the routed WAN interface created in the “

Creating the WAN Service

” section.

6.

Select a “Precedence” of 1.

NOTE

Lower values of

“Precedence” indicate HIGHER priority.

7.

Leave the “DSL Latency” value set to Path0 and

Click Apply/Save.

8.

Create the IPTV queue by selecting

Advanced Setup -> Quality of Service -> QoS Queue

Config

and click Add.

Figure 39 QoS: IPTV Queue Configuration

9.

Name, enable and select the WAN interface to be fed by this queue.

IMPORTANT

NOTE

Again, select the routed WAN interface creat

ed in the “

Creating the WAN Service

”

section.

10.

Select a “Precedence” of 2.

NOTE

IPTV traffic should be of LOWER priority (HIGHER Precedence value) than VoIP traffic.

SmartRG™ Resi

dential Gateways

P a g e

| 48

C o n f i d e n t i a l

S m a r t R G © 2 0 1 2

11.

Leave the “DSL Latency” value set to Path0 and Click

Apply/Save.

NOTE

The default data queue depicted in the QoS architecture diagram above does not need

to be specifically created.

12.

Enable the newly created queues by selecting

Advanced Setup -> Quality of Service -> QoS

Queue Config,

check the “Enable” boxes for

the new queues and click Enable. The correct

queue configuration for VoIP and IPTV services should look like:

Figure 40 QoS Queue Enable

Configuring Your SmartRG™

- Common Use Cases

S m a r t R G © 2 0 1 2

C o n f i d e n t i a l

P

a

g

e

| 49

13.

Create the VoIP traffic classifier by selecting

Advanced Setup -> Quality of Service -> QoS

Classification

and click Add.

Figure 41 QoS VoIP Classifier Configuration

14.

Set the Name, Rule Order, and enable the classifier rule.

IMPORTANT

NOTE

If you create the classifier rules in priority order (VoIP then IPTV), you may leave the

“Rule Order” set to “Last.” Each successive classifier rule created will become the

last one checked in the traffic identification process.

15.

Select an

“

Ether Type

” of

IP (0x800).

16.

Enter the source MAC and Mask values in 01:02:03:04:05:06/FF:FF:FF:00:00:00 format.

17.

Assign the Classification Queue (identified by WAN interface&Precedence&Path).

18.

Click Apply/Save.

SmartRG™ Resi

dential Gateways

P a g e

| 50

C o n f i d e n t i a l

S m a r t R G © 2 0 1 2

19.

Create the IPTV traffic classifier by selecting

Advanced Setup -> Quality of Service -> QoS

Classification

and click Add.

Figure 42 QoS IPTV Classifier Configuration

20.

Set the Name, Rule Order, and enable the classifier rule.

IMPORTANT

NOTE

If you create the classifier rules in priority order (VoIP then IPTV), you may leave the

“Rule Order” set to “Last.” Each s

uccessive classifier rule created will become the

last one checked in the traffic identification process.

21.

Select an “Ether Type” of IP (0x800).

22.

Enter the “Differentiated Service Code Point (DSCP) Check” value.

NOTE

AF21 (DSCP18) is common for Mediaroom STBs.