Sitecom X4 N300 Router Manual PDF (Setup & Configuration Guide)

Page 16 / 48 Scroll up to view Page 11 - 15

IPv6 Configuration (Firmware 2.0 and up only)

The IPv6 (Internet Protocol version 6) section is where you configure your IPv6

Connection type.

IPv6 Connection Type

There are several connection types to choose from: Static IPv6, Autoconfiguration, 6RD

and Link-local only. If you are unsure of your connection method, please contact your

IPv6 Internet Service Provider.

Static IPv6 Mode

This mode is used when your ISP provides you with a set IPv6 addresses that does not

change. The IPv6 information is manually entered in your IPv6 configuration settings.

You must enter the IPv6 address, Subnet Prefix Length, Default Gateway, Primary DNS

Server and Secondary DNS Server. Your ISP provides you with all this information.

Page 17 / 48

6RD Mode

In the 6RD mode, no additional configuration is necessary.

Link-local Mode

The Link-local address is used by nodes and routers when communicating with

neighboring nodes on the same link. This mode enables IPv6-capable devices to

communicate with each other on the LAN side.

Page 18 / 48

Configure your Router

Status

The System status section allows you to monitor the current status of your router, the UP

time, hardware information and serial number as well as firmware version information is

displayed here.

DHCP Server

The DHCP Server tab gives you the opportunity to change the IP settings of the router.

Click

Apply

at the bottom of this screen to save any changes.

Page 19 / 48

•

IP address 192.168.0.1

:

It is the router’s LAN IP address (Your LAN clients

default gateway IP address).

•

IP Subnet Mask 255.255.255.0

: Specify a Subnet Mask for your LAN

segment.

•

802.1d Spanning Tree

: Disabled by default. If the 802.1d Spanning Tree

function is enabled, this router will use the spanning tree protocol to prevent

network loops.

•

DHCP Server

: Enabled by default. You can enable or disable the DHCP server.

When DHCP is disabled no ip-addresses are assigned to clients and you have

to use static ip-addresses. When DHCP server is enabled your computers will

be assigned an ip-address automatically until the lease time expires.

•

Lease Time

: One Week. In the Lease Time setting you can specify the time

period that the DHCP lends an IP address to your LAN clients. The DHCP will

change your LAN client’s IP address when this time threshold period is

reached.

•

IP Address Pool

: You can select a particular IP address range for your DHCP

server to issue IP addresses to your LAN Clients. The default IP range is

192.168.0.100 ~ 192.168.0.200. If you want your PC(s) to have a static/fixed

IP address, then you’ll have to choose an IP

address outside this IP address

Pool

•

Domain Name

: You can specify a Domain Name for your LAN or just keep the

default (sitecomwlr4100).

Device Status

View the r

outer’s current configuration settings. Device Status displays the configuration

settings you’ve configured in the

Internet Settings and WiFi Settings sections.

Page 20 / 48

Internet Status

This page displays whether the WAN port is connected to a Cable/DSL connection. It also

displays the router’s WAN IP address, Subnet Mask, and ISP Gateway as well as MAC

address, the Primary DNS. Press Renew button to renew your WAN IP address.

DHCP Client Status

This page shows all DHCP clients (LAN PCs) currently connected to your network. The

table shows the assigned IP address, MAC address and expiration time for each DHCP

leased client. Use the Refresh button to update the available information.

You can check

“

Enable Static DHCP IP

”

. It is possible to add more static DHCP IPs. They

are listed in the table Current Static DHCP Table. IP can be deleted at will from the table.

Click

Apply

to save the changed configuration.

Rate

Popular Sitecom Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share