Sitecom WL-312 Router Manual PDF (Setup & Configuration Guide)

Page 31 / 60 Scroll up to view Page 26 - 30

31

ACL

This wireless router supports MAC Address Control, which prevents

unauthorized clients from accessing your wireless network.

Enable wireless access control

Enables the wireless access control function

Adding an address into the list

Enter the "MAC Address" and "Comment"

of the wireless station to be added and then click "Add". The wireless station

will now be added into the "Current Access Control List" below. If you are

having any difficulties filling in the fields, just click "Clear" and both "MAC

Address" and "Comment" fields will be cleared.

Remove an address from the list

If you want to remove a MAC address

from the "Current Access Control List ", select the MAC address that you want

to remove in the list and then click "Delete Selected". If you want to remove

all the MAC addresses from the list, just click the "Delete All" button. Click

"Reset" will clear your current selections.

Click <Apply> at the bottom of the screen to save the above configurations.

You can now configure other sections by choosing Continue, or choose Apply

to apply the settings and reboot the device.

Page 32 / 60

32

WPS

Wi-Fi Protected Setup (WPS) is the simplest way to establish a connection

between the wireless clients and the wireless router. You don’t have to select

the encryption mode and fill in a long encryption passphrase every time when

you try to setup a wireless connection. You only need to press a button on

both wireless client and wireless router, and WPS will do the rest for you.

The wireless router supports two types of WPS: WPS via Push Button and

WPS via PIN code. If you want to use the Push Button, you have to push a

specific button on the wireless client or in the utility of the wireless client to

start the WPS mode, and switch the wireless router to WPS mode. You can

simply push the WPS button of the wireless router, or click the ‘Start to

Process’ button in the web configuration interface. If you want to use the PIN

code, you have to know the PIN code of the wireless client and switch it to

WPS mode, then fill-in the PIN code of the wireless client through the web

configuration interface of the wireless router.

WPS

Check the box to enable WPS function and uncheck it to disable the

WPS function.

WPS Current Status

If the wireless security (encryption) function of this

wireless router is properly set, you’ll see a ‘Configured’ message here.

Otherwise, you’ll see ‘UnConfigured’.

Page 33 / 60

33

Self Pin Code

This is the WPS PIN code of the wireless router. You may need

this information when connecting to other WPS-enabled wireless devices.

SSID

This is the network broadcast name (SSID) of the router.

Authentication Mode

It shows the active authentication mode for the

wireless connection.

Passphrase Key

It shows the passphrase key that is randomly generated by

the wireless router during the WPS process. You may need this information

when using a device which doesn’t support WPS.

WPS via Push Button

Press the button to start the WPS process. The router

will wait for the WPS request from the wireless devices within 2 minutes.

WPS via PIN

You can fill-in the PIN code of the wireless device and press the

button to start the WPS process. The router will wait for the WPS request

from the wireless device within 2 minutes.

Page 34 / 60

34

12

Firewall Settings

The Broadband router provides extensive firewall protection by restricting

connection parameters, thus limiting the risk of hacker attacks, and defending

against a wide array of common Internet attacks. However, for applications that

require unrestricted access to the Internet, you can configure a specific

client/server as a Demilitarized Zone (DMZ).

Note

: To enable the Firewall settings select Enable and click Apply

Page 35 / 60

35

DMZ

If you have a client PC that cannot run an Internet application (e.g. Games)

properly from behind the NAT firewall, then you can open up the firewall

restrictions to unrestricted two-way Internet access by defining a DMZ Host.

The DMZ function allows you to re-direct all packets going to your WAN port

IP address to a particular IP address in your LAN. The difference between the

virtual server and the DMZ function is that the virtual server re-directs a

particular service/Internet application (e.g. FTP, websites) to a particular LAN

client/server, whereas DMZ re-directs all packets (regardless of services)

going to your WAN

IP address to a particular LAN client/server.

Enable DMZ

Enable/disable DMZ

Public IP Address

The IP address of the WAN port or any other Public IP

addresses given to you by your ISP

Client PC IP Address

Fill-in the IP address of a particular host in your LAN

that will receive all the packets originally going to the WAN port/Public IP

address above.

Click

<Apply>

at the bottom of the screen to save the above configurations.

Rate

Popular Sitecom Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share