1. Home
    2. /
  2. Manuals
    3. /
  3. Sierra Wireless
    4. /
  4. SWAC802
    5. /
  5. 17
Page 81 / 174 Scroll up to view Page 76 - 80
Settings
73
Settings
●
Import Router Settings
— You can import configuration settings. (See “Importing Settings” on
page 108.)
●
Export Router Settings
— You can export configuration settings. (See “Exporting Settings” on
page 108.)
●
Update Firmware from File
— You can upgrade the device firmware from a file. (See “Upgrading
Firmware From a File” on page 59.)
●
Standby Timer on Battery
and
On AC Power
— You can enable standby (low power) mode. (See
“Standby (Low Power) Mode” on page 45.)
●
TRU-Install
— This feature installs the necessary drivers the first time you connect your device to
your Windows or Mac computer through the micro-USB cable. (For information on this feature,
see “TRU-Install” on page 26.)
●
Check for Updates
and
Check for updates now
— You can check for updates to your device.
(See “Automatically Checking for Updates” on page 57 and “Manually Checking for Updates”
on page 58.)
Display Panel
From the
Display
panel of the
Device
tab, you can configure settings for the device LCD.
To access this panel:
1.
Log in to the home page.
2.
Click
Advanced Settings
(
).
3.
Click
Device > Display
.
From this window, you can view or adjust these settings:
●
Power Button LED
— You can enable the power button light on the device. (See “Enabling and
Disabling the Power Button LED” on page 68.)
●
LCD Backlight
— You can turn the LCD on or off. (See “Turning the LCD On or Off” on page 67.)
●
Turn Backlight Off
— This setting specifies how soon the LCD goes dormant. (See “Setting the
LCD Timeout” on page 67.)
●
Backlight Settings
— You can adjust the brightness of the LCD. (See “Setting the LCD
Brightness” on page 67.)
microSD Card Panel
1.
Log in to the home page.
2.
Click
Advanced Settings
(
).
3.
Click
Device > microSD Card
.
From this window, you can view or adjust these settings, or perform the following actions:
●
Status
— This field reflects the status of the microSD card slot (for example, the slot is disabled,
or a card is detected).
Downloaded from
www.Manualslib.com
manuals search engine
Page 82 / 174
74
Settings
●
SD-Card Slot
— Before you can use the microSD Card slot, you must enable it. (See “Enabling the
microSD Card Slot” on page 51.)
●
microSD Shared Folder Name
— This is the name of the folder that the microSD card shows up as
(in the file browser program). (See “microSD Shared Folder Name” on page 52.)
●
Username and Password Security
— You can specify whether a username and password are
required to access the microSD Card. (See “Setting Up Access to the microSD Card” on page 51.)
●
Guest Username
— This is the username that non-administrators must enter before using the card.
●
Guest Password
— This is the password that non-administrators must enter before using the card.
Sounds Panel
From the
Sounds
panel of the
Device
tab, you can enable or disable sounds for specific types of
events. To enable or disable sounds:
1.
Log in to the home page.
2.
Click
Advanced Settings
(
).
3.
Click
Device > Sounds
.
4.
Next to each of the event types, select
Enable
or
Disable
.
Sounds for the following events can be individually enabled or disabled:
●
Low Battery
— A sound is played when the battery is low. This is useful as a reminder to charge the
device. In the
Alert When
list, you can select a battery level to trigger the alert.
●
System Alerts
— A sound is played when a system alert occurs. You can then use the device LCD
or the Alerts window to get information about the alert. (See “Alert Information” on page 42.)
●
Internet Connected
— A sound is played when you connect to the Internet.
●
Internet Disconnected
— A sound is played when you lose the connection to the Internet.
●
Wi-Fi User Has Joined
— Useful, for example, if you’re the only one using the device, to detect an
intruder.
●
Wi-Fi User Has Left
— A sound is played when a Wi-Fi user disconnects from your network.
●
Last User Has Left
— A sound is played when the last Wi-Fi user disconnects from your network.
You can turn the device off if nobody will be using it for awhile.
●
Enter Standby Mode
— A sound is played when the device enters standby mode. See “Standby
(Low Power) Mode” on page 45.
To play the sound for an event, click its
button.
Note:
System alerts include several types of events, for example:
• Critical battery
• Critical temperature
• Software update available
• Routing hardware settings reset
• Device startup failure
Downloaded from
www.Manualslib.com
manuals search engine
Page 83 / 174
Settings
75
Settings
About Panel
To view information about your device:
1.
Log in to the home page.
2.
Click
Advanced Settings
(
).
3.
Click
Device > About
.
The following information is displayed:
●
Model Number
— This is the manufacturer’s model of your device.
●
Activation Status
— This field reflects whether 3G is activated.
●
Manufacturer
— This is the company that made your device.
●
Activation Date
— This is the date that the 3G modem was first activated.
●
Software Version
— This is the firmware version for the routing hardware of the device.
●
Network Operator
— This field shows the carrier that your device was activated with.
●
Reconditioned Status
— This field indicates whether your device has been returned for service
or repair and reconditioned (if applicable).
●
Wi-Fi Firmware Version
— This is the firmware version for the Wi-Fi access point of the device.
●
Reconditioned Date
— This field indicates the date that your device has been reconditioned (if
applicable).
●
Router PRI Version
— This is the PRI version for the routing hardware of the device. The PRI
(Product Release Instructions) is a file that contains the settings used to configure wireless
products for a particular service provider, customer, or purpose.
●
Total Bytes
— This is the amount of data transferred over the 3G network during the lifetime of
the device.
●
MDN
(Mobile Directory Number) — This is a 10-digit phone number.
●
ESN
or
MEID
.
The ESN (Electronic Serial Number) is the unique first-generation serial number assigned to the
3G component of the device.
The MEID (Mobile Equipment Identifier) is the unique second-generation serial number
assigned to the 3G component of the device.
●
PRL Version
— The PRL (Preferred Roaming List) is an account configuration item set by your
service provider. It controls the radio channels and network carrier used by the 3G modem.
●
PRI Version
— This is the PRI version of the 3G component of the device.
●
Firmware Version
— This is the firmware version of the 3G component of the device.
●
Total Bytes
— This is the amount of data transferred over the 4G network during the lifetime of
the device.
Note:
4G information is not available if
WAN mode
is “3G only.” (
WAN mode
is in
Advanced
Settings > WAN > Setup
.)
Downloaded from
www.Manualslib.com
manuals search engine
Page 84 / 174
76
Settings
●
Firmware Version
— This is the firmware version of the 4G component of the device.
●
MAC Address
— This is the MAC address of the 4G module. Each wireless device has a unique
MAC address (assigned by its manufacturer).
●
Plan Version
— This is the version information of your 4G channel plan, which determines the
frequencies to scan and 4G networks to detect.
The window also has buttons to:
●
Save the information to a text file.
●
Reset the 3G and 4G configuration of the device to default settings (
Reset Device to Factory
Defaults
). (See “Resetting the 3G and 4G Configurations to Default Settings” on page 92.)
Log Panel
1.
Log in to the home page.
2.
Click
Advanced Settings
(
).
3.
Click
Device > Log
.
From this window, you can:
●
Enable logging of system events. (See “Enabling and Disabling Logging of System Events” on
page 110.)
●
Export logs. (See “Exporting System Events” on page 110 and “Exporting the Connection History”
on page 109.)
●
Clear logs. (See “Clearing the System Events Log” on page 110 and “Clearing the Connection
History” on page 109.)
●
Enable logging of connects and disconnects. (See “Enabling and Disabling Logging of Connects
and Disconnects” on page 109.)
●
Set the method used for time acquisition. (See “Setting the Method Used for Time Acquisition” on
page 111.)
WAN Tab
Setup Panel
1.
Log in to the home page.
2.
Click
Advanced Settings
(
).
3.
Click
WAN > Setup
.
Tip:
You can view some of the above information on the “About...” LCD information screen. (See “LCD
Information Screens” on page 17.)
Downloaded from
www.Manualslib.com
manuals search engine
Page 85 / 174
Settings
77
Settings
From this window, you can view or adjust these settings, or perform the following actions:
●
Active Network
— This is the network that is currently being used for your data connection: 3G,
4G, or none.
●
Network Operator
— This field shows the carrier that your device was activated with.
●
Session Duration
— The session duration indicates how long you’ve been connected to the
network.
●
Session Total Data
— This indicates the amount of data transferred over the lifetime of the device
(by network type) and in the current session.
●
Work Mode
— This indicates the 3G and 4G activation/provisioning status of your device and
account. Technical support staff may request this value from you.
●
WAN Mode
— This setting specifies the network(s) to connect to, and in what order.
±
3G preferred
— The connection can be established to either 3G or 4G; if both are available,
3G is used.
±
4G preferred
— The connection can be established to either 3G or 4G; if both are available,
4G is used. This setting is recommended if your service provider has no data limit for 4G,
but does for 3G, or you want to take advantage of the faster data transfer speeds of 4G.
±
3G only
— The connection can be established only to 3G. (If you don’t have 4G coverage,
you can save power by selecting
3G Only
.)
±
4G only
— The connection can be established only to 4G.
●
Connect Automatically
— You can set your device to connect to the network when the device
powers on.
●
Failover Wait-time
— This setting specifies how long the device should wait, after it loses the
connection with the preferred network, before it attempts to connect to the other network (not
available if
WAN mode
is “3G only” or “4G only”).
●
Switchback Wait-time
— This setting specifies how long the device should wait, when the less-
preferred network is connected and the preferred network becomes available, before switching
to the preferred network (not available if
WAN mode
is “3G only” or “4G only”).
3G Panel
See “3G Panel” on page 91.
4G Panel
1.
Log in to the home page.
2.
Click
Advanced Settings
(
).
3.
Click
WAN > 4G
.
Note:
4G information is not available if
WAN mode
is “3G only.” (
WAN mode
is in
Advanced
Settings > WAN > Setup
.)
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4 / 5 based on 1 vote.

Popular Sierra Wireless Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top