Page 51 / 102 Scroll up to view Page 46 - 50
SpeedStream Wireless DSL Gateway
Advanced Features
45
Gateway
The
Gateway
option provides access to all Gateway configuration options, security settings, Gateway
health monitoring screens, and Internet connection and network details. The options that display under the
Modem Options heading in the left-navigation-pane are based on how you logged into the system.
If you
logged in as the administrator, all options are turned on and enabled.
If you logged in as a user, only the
Gateway Health, Customize, and Reboot options are enabled.
Figure 38: Gateway Window (with Administrator Log on)
ISP Connection
All active and available Internet connections are shown in this window. Many of the settings for this
option are intended for use by advanced users. This option may not be available depending on your ISP.
Note
: You must be logged in as an administrator to use this option.
WARNING
: You may terminate your Internet connection if this feature is not properly configured.
To use the ISP connection function:
1.
Log on as the administrator.
2.
Click
Gateway
in the toolbar.
3.
Click
ISP Connection
in the left-navigation-pane.
The system responds with the “ISP Connection
Information” window.
Page 52 / 102
SpeedStream Wireless DSL Gateway
Advanced Features
46
4.
Click one of the ISP connections (in red) to reconfigure that connection.
Please check with your ISP
for the information required to reconfigure a connection.
Figure 39: ISP Connection Information Window
5.
Click
Advanced Settings
to configure additional access options from your ISP.
The system responds
with the “Advanced Internet Options” window.
Figure 40. Advanced Internet Options Window
6.
Please see the next section in this document titled
Advanced Internet Options
.
Page 53 / 102
SpeedStream Wireless DSL Gateway
Advanced Features
47
Advanced Internet Options
All of the options in this section should only be configured with the help and guidance of your ISP.
Incorrect changes to any of these options, could result in the failure of your Internet connection.
ATM Virtual Circuits
The ATM virtual circuit option provides access to settings that your Internet Service Provider may advise
you to modify depending upon your service needs. This option allows the creation and configuration of a
PVC (Permanent Virtual Circuit) across a network.
A PVC is used to maintain a permanent connection
between two points on a network.
Note
:
ATM Setting changes should not be made unless you are
advised to do so by your Internet Service Provider
.
To access the ATM virtual circuit option:
1.
Click
Advanced Settings
.
The system responds with the “Advanced Internet Options” window.
Figure 41: ATM Virtual Circuits Screen
2.
Click the “Configure ATM Virtual Circuit” hyperlink.
The system responds with the “ATM Virtual
Circuit Wizard” window.
Static Routes
The static routes option allows you to configure static routes to remote equipment. These routes appear in
the routing table.
Static routing allows a pre-defined route to be set for the transmission of data.
Static
routes take precedence over all dynamic routing options and also provide enhanced security over dynamic
routing.
Page 54 / 102
SpeedStream Wireless DSL Gateway
Advanced Features
48
To use the static route option:
1.
Click
Advanced Settings
.
The system responds with the “Advanced Internet Options” window.
2.
Click the “Add Static Routes for Direct IP Connections” hyperlink.
The system responds with the
“Static Routes” window.
Figure 42: Static Routes Window
3.
Type the IP address of the destination device in the “Destination” box.
4.
Optionally
, click the “View the current routing table” hyperlink to view the current routing table.
Please see the section in this document titled
Routing Table
for more information.
5.
Type the net mask of the destination device in the “Net Mask” box.
6.
Optionally
, type the IP address of a destination gateway in the “Next Hop” box.
7.
Select a connection type from the “Interface” drop-down.
8.
Click
Apply
.
The system responds by adding your new route to the routing table.
Page 55 / 102
SpeedStream Wireless DSL Gateway
Advanced Features
49
Routing Table
This screen shows a table of routing information including Destination IP Address, Subnet Mask, Flags,
Gateway, Metric and Interface of all static and dynamic routes for network devices.
To access the routing table:
1.
Log on as the administrator.
2.
Click
Gateway
in the toolbar.
3.
Click
ISP Connection
in the left-navigation-pane.
4.
Click
Advanced Settings
.
The system responds with the “Advanced Internet Options” window.
5.
Click the “View the Current Routing Table” hyperlink.
The system responds with the “Current
Routing Table” window.
Figure 43: Routing Table Window
Dynamic DNS
Dynamic DNS translates IP addresses into alphanumeric names.
For example, an IP address of
333.136.249.80 could be translated into efficient.com.
To use the DDNS service:
1.
You must register for the service at
there is no fee for this
service.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top