Siemens Gigaset-SE572 Router Manual PDF (Setup & Configuration Guide)

Page 116 / 148 Scroll up to view Page 111 - 115

116

Installing the printer port for network printers

ì

If you wish to install a printer for this port immediately, click on

printer installation wizard's instructions.

ì

If you do not wish to install a printer until later, click on

Cancel

.

Note:

The Gigaset SE551 WLAN dsl/cable's printer server does not work bidirectionally. It

does not evaluate any of the printer's response messages. For this reason please make

sure that your printer is also configured unidirectionally. You can make the relevant

printer settings for your printer via

Start

–

Settings

–

Printer

.

Page 117 / 148

117

Installing the printer port for network printers

Installing a printer on the TCP/IP port retrospectively

If you connect a printer to this port at a later time, start as described above for installing

the printer port.

ì

In this case, however, you should click on the selection menu in the

Select a Printer

Port

window.

ì

Select from the list the connection you have set up: e.g.

Gigaset_Druckerport

(Standard TCP/IP Port)

.

ì

Click on

that follow.

Page 118 / 148

118

Installing the printer port for network printers

Installing a printer driver under Windows 98 SE or ME

The following section describes how to install a printer driver under the Windows 98 SE

or ME operating systems as the procedure and windows shown for these operating sys-

tems are very similar. The printer driver does not need to be installed on Windows XP

and 2000.

You have installed your network and it is ready for use.

ì

Insert the CD-ROM included in the scope of delivery into the CD-ROM or DVD drive

of your PC.

ì

Wait until the CD-ROM welcome window appears.

ì

Click on Gigaset SE551 WLAN dsl/cable.

ì

Click on

Printer Port Driver

for Windows 98 SE or ME.

The welcome window for installing the port driver is opened.

ì

Read the information it contains carefully.

ì

Click on

The necessary files are copied to your PC and executed. Once all the data has been

transferred to your PC you are prompted to complete the installation of the port

driver.

ì

Click on

Finish

.

ì

Reboot your PC.

You have now installed the printer port and effectively installed an extra printer inter-

face in your PC.

You must carry out this installation on every PC with Windows 98 or ME that is to use

this printer in the network.

You might possibly still have to correct the IP address for the printer.

ì

Select

Start

–

Settings

–

Printer

, select the printer and right-click on the mouse to

open the pop-up menu.

ì

Select

Properties

and open the

Details

tab.

ì

Select the port and click on

Connection Settings

.

ì

Change the IP address if necessary. It must be the same as that for the Gigaset SE551

WLAN dsl/cable.

Page 119 / 148

119

Installing the printer port for network printers

Instructions for setting up a printer on the PC

Once you have installed the printer port you still cannot start printing. The printer port

is nothing more than an additional interface on your PC, comparable with the USB port.

It means that any printer you install on this port is also regarded as a local printer even

though it is located in the network and possibly remote from you.

You still need to connect and configure the printer to this port.

ì

Connect the printer to the USB interface on your Gigaset SE551 WLAN dsl/cable.

The printer is installed in the same way as any other printer:

ì

Go through

Start

–

Settings

–

Printer

and click on

New Printer

.

ì

In the window that opens, click on

ì

Proceed as instructed by the printer installation wizard. Please note:

In the window in which you are prompted to specify the location of the printer you

should select

Local Printer

(usually the default setting).

ì

Then click on

ì

Continue to install the printer. Select your printer and click on

ì

When the window appears in which you are prompted to enter the type of connec-

tion, double click on the port name

Gigaset_Druckerport

.

ì

Then continue to install the printer and finish the installation.

Note:

The Gigaset SE551 WLAN dsl/cable's printer server does not work bidirectionally. It

does not evaluate any of the printer's response messages. For this reason please make

sure that your printer is also configured unidirectionally.

Page 120 / 148

120

Appendix

Deactivating HTTP proxy and configuring pop-up blocker

To start the configuration program, you may need to deactivate your browser's

HTTP proxy. If you use Windows Vista or Windows XP Service Pack 2, you will need to

configure the popup blocker. Both procedures are described on the next pages.

Deactivating the HTTP proxy

Make sure that the

HTTP Proxy

in your web browser is deactivated. This function must

be deactivated so that your web browser can access your Gigaset SE551 WLAN dsl/

cable's configuration pages.

The following section describes the procedure for Internet Explorer and Mozilla Firefox.

First decide which browser you are using and then follow the appropriate steps.

u

Internet Explorer

ì

Open Internet Explorer and from the

Tools

menu select

Internet Options

.

ì

In the

Internet Options

window click the

Connections

tab.

ì

Click

LAN Settings

.

ì

Deactivate all options in the

LAN Settings

window.

ì

Click

OK

and then

OK

again to close the

Internet Options

window.

u

Mozilla Firefox

ì

Open Mozilla Firefox. Click

Tools

and then

Settings

.

ì

In the

Settings

window, click

Connection Settings...

ì

In the

Connection Settings

window, select the option

Direct connection to the

Internet

.

ì

Click

OK

to finish.

Rate

Popular Siemens Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share