Siemens Gigaset-SE551 Router Manual PDF (Setup & Configuration Guide)

Page 16 / 148 Scroll up to view Page 11 - 15

16

First Steps

Contents

The package contains the following items:

u

one Gigaset SE551 WLAN dsl/cable,

u

one mains adapter (220 V / 12V 1A DC),

u

one cable with RJ-45 jacks (CAT5),

u

one CD with full user guide and driver software for operating a network printer on

the Gigaset SE551 WLAN dsl/cable via Windows 98 SE / ME, plus the documents enti-

tled "Gigaset WLAN. Practical tips" and "Network configuration“,

u

one Quick Start Guide

System requirements

To operate your Gigaset SE551 WLAN dsl/cable you need:

u

a PC with

–

an 802.11g or 802.11b-compatible wireless

Network adapter

.

In order to be able to use the superior range and increased data throughput

gained by using Super G technology, we recommend using a Gigaset PC Card 108

or a Gigaset USB Adapter 108.

or

–

an

Ethernet

connection,

u

a Web browser such as Microsoft Internet Explorer 6.0 or Mozilla Firefox 1.0 for

configuring your Gigaset SE551 WLAN dsl/cable

u

for Internet access

–

a DSL or cable modem and a splitter (for DSL),

–

the access data for your

Internet Providers

.

Note:

The maximum data transfer rate for 802.11b-compatible network adapters is

11 Mbps, for 802.11g-compatible network adapters 54 Mbps, and for network

adapters that support Super G, 108 Mbps.

You can only achieve the transfer rate of 108 Mbps during operation if all net-

work adapters registered in the wireless network support Super G.

Page 17 / 148

17

First Steps

Operating displays and connections

Front panel

LED displays

The front panel of the device contains LED displays that show the operating state and

simplify installation and fault finding in the network.

The LEDs show the following (from right to left):

LED

State

Status

USB

On

A device is connected to the Gigaset SE551 WLAN dsl/

cable via the USB port.

Off

There is no device connected.

Power

On

The Gigaset SE551 WLAN dsl/cable is connected to the

power supply.

Off

The Gigaset SE551 WLAN dsl/cable is not connected to the

power supply.

WAN

On

A DSL or cable modem is connected.

Flashing

The WAN port is sending or receiving data (traffic).

Off

There is no modem connected.

Online

On

Connection to the Internet has been established.

Off

There is no Internet connection.

Page 18 / 148

18

First Steps

Back panel

The back panel of the Gigaset SE551 WLAN dsl/cable houses the sockets.

Reset

The reset button is located behind the small opening on the bottom of the device.

WLAN

On

The radio interface is active.

Flashing

The Gigaset SE551 WLAN dsl/cable is sending or receiving

data on the radio interface.

Off

The radio interface has been deactivated or no radio sig-

nal is being received.

LAN1 –

LAN4

On

A device is connected to the relevant LAN port.

Flashing

The LAN port is sending or receiving data (traffic).

Off

There is no device connected.

Element

Description

12 V DC

Socket for the mains adapter supplied (12V 1A DC).

Warning

: Using the wrong power supply unit may damage the

Gigaset SE551 WLAN dsl/cable.

Modem

Socket for connecting to the DSL or cable modem.

LAN1 –

LAN4

Four 10/100

Mbps

switch sockets with automatic recognition (RJ-45).

You can connect up to four Ethernet devices (such as PCs, a

Hub

or

Switch

).

USB

USB port for printer or USB bulk memory.

LED

State

Status

Page 19 / 148

19

First Steps

u

Reboot function: Press the button for longer than 1 second but less than 5 seconds

to reboot the device. This does not affect the configuration settings.

u

Reset function: Press the button behind the small opening on the bottom of the

device for at least 5 seconds to return all settings to the factory settings.

Warning

: This will clear all the configuration settings you have made.

Updated firmware will not be affected.

Setting up the Gigaset SE551 WLAN dsl/cable

The Gigaset SE551 WLAN dsl/cable can be set up in any suitable location in your home

or office. You do not need any special wiring. However you should comply with the fol-

lowing guidelines:

u

Operate the Gigaset SE551 WLAN dsl/cable only indoors within a temperature range

of +5 to +40 °C. Do not position the Gigaset SE551 WLAN dsl/cable near sources of

heat. Do not cover the ventilation slots. High temperatures can damage the device.

u

A mains socket for 220/240V~ and a connection socket for the modem or LAN must

be available where you set up the Gigaset SE551 WLAN dsl/cable.

u

Do not site the device in the immediate vicinity of stereo equipment, TV sets or

microwave ovens. This may cause interference.

u

Position the Gigaset SE551 WLAN dsl/cable so that it is as near to the centre of your

wireless network as possible. Make sure that where you position the Gigaset SE551

WLAN dsl/cable has optimum reception throughout the house or office. You can

improve the reception quality by aligning the antenna (turn and/or tilt).

u

Position the Gigaset SE551 WLAN dsl/cable on a non-slip surface. The router feet do

not normally leave any traces on the surface they are on. However, some furniture

surfaces may contain substances that attack and soften the router's rubber feet.

Then the feet may well mark the furniture surface.

u

Do not place the Gigaset SE551 WLAN dsl/cable on any furniture surface that could

be affected by the heat from the device.

u

Position the Gigaset SE551 WLAN dsl/cable so that it cannot fall.

u

Lay the cables so that nobody can trip over them.

u

If you wish to mount the Gigaset SE551 WLAN dsl/cable on the wall, use flat-headed

or tallow-drop screws with a maximum thread diameter of 3.5mm. The screws are

not included in the scope of delivery.

Page 20 / 148

20

First Steps

Connecting the Gigaset SE551 WLAN dsl/cable

Before starting to connect PCs to your Gigaset SE551 WLAN dsl/cable make sure that

u

a wired or wireless

Network adapter

is connected to the PC. Please read the operat-

ing instructions that came with the adapter. The latest PCs and Notebooks have

wired adapters built in at the factory.

u

ConnectionPoint

has been entered as

SSID

on the network adapter.

To the DSL or cable modem

ì

Connect the socket on the back of the router marked

DSL

and your DSL or cable

modem with an Ethernet cable.

Please remember:

Use a category 5 Ethernet cable with RJ-45 jacks on both ends for all connections.

DSL or cable modem

Rate

Popular Siemens Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share