Page 16 / 51 Scroll up to view Page 11 - 15
C2-010 / C2-010-I ADSL2+ Router User’s Guide
4.2.1 Configuring a Bridged Connection for the WAN
A bridged connection between your ISP and your LAN (the computers in your house or office) is the
simplest type of connection possible.
The ADSL2+ Router will simply convert the incoming and outgoing
packets to the correct format for each side of the connection (Ethernet for the LAN, ATM for the WAN).
For a bridged connection it will be necessary for most users to install additional software (supplied by
your ISP) on any computer that will use the ADSL2+ Router for Internet access. The additional software is
used for the purpose of identifying and verifying your account, and then granting Internet access to the
computer requesting the connection (that is, the software supplied by your ISP will handle giving your
Username and Password to the computer at your ISP that will then connect you to the Internet). The
connection software requires the user to enter the User Name and Password for the ISP account. This
information is stored on the computer on the LAN, not in the ADSL2+ Router for a bridged connection.
Follow the instructions below to configure a Bridged connection for the WAN interface.
Figure 4-4 WAN Settings Menu – Bridge Mode
Note:
Please note that the menu shown above will change depending on which WAN Type and Connection
Type you select.
To configure a Bridged mode connection, perform the steps listed below. Some of the settings do not need
to be changed the first time the device is set up, but can be changed later if you choose. See the table below
for a description of all the settings available in this menu.
1. Choose the
Bridge Mode
option from the
WAN Settings
pull-down menu.
2. Under the
ATM Interface
settings at the top of the menu (including
VPI
,
VCI
, and
Virtual Circuit
) should
not be changed unless you have been instructed to change them. However, if you are instructed to change
the
VPI
or
VCI
values, type in the values assigned for your account. Leave the
ATM Interface
and
Virtual
Circuit
setting at the default (
Pcv0
and
Enabled
) values for now. This can be used later if you are
configuring multiple virtual circuits for your ADSL service.
3. Under the
Bridge Mode
heading, choose the
Connection Type
from the pull-down menu. This defines
both the connection type and encapsulation method used for your ADSL service. The available options are
1483 Bridged IP LLC
and
1483 Bridged IP VC-Mux.
If have not been provided specific information for the
Connection Type setting, leave the default setting.
4-4
Downloaded from
www.Manualslib.com
manuals search engine
Page 17 / 51
ADSL2+ Router User’s Guide
4. When you are satisfied that all the WAN settings are configured correctly, click on the
Apply
button.
Note:
Some accounts use PPP connection software for their Internet service connection.
If you have been
given a CD with PPP connection software, install this now as instructed by your service provider. After the
ADSL2+ Router has rebooted it will negotiate the ADSL connection. Use the connection software to log on to
the ISP network and access the Internet.
4.2.2
Static IP Address for Connection WAN
When the Router is configured to use Static IP Address assignment for the WAN connection, you must
manually assign a global IP Address, Subnet Mask and Gateway IP Address used for the WAN connection.
Most users will also need to configure DNS server IP settings in the DNS Settings configuration menu (see
below). Follow the instruction below to configure the Router to use Static IP Address assignment for the WAN
connection.
To configure a Static IP Address connection, perform the steps listed below. Some of the settings do not
need to be changed the first time the device is set up, but can be changed later if you choose. See the table
below for a description of all the settings available in this menu.
Figure 4-5 WAN Settings Menu – Static IP Address
To configure a Static IP type connection for the WAN, follow these stpes:
1. Choose the
Static IP Address
option from the
WAN Settings
pull-down menu.
2. Under the
ATM Interface
settings at the top of the menu (including
VPI
,
VCI
, and
Virtual Circuit
) should
not be changed unless you have been instructed to change them. However, if you are instructed to change
the
VPI
or
VCI
values, type in the values assigned for your account. Leave the
ATM Interface
and
Virtual
Circuit
setting at the default (
Pcv0
and
Enabled
) values for now. This can be used later if you are
configuring multiple virtual circuits for your ADSL service.
4-5
Downloaded from
www.Manualslib.com
manuals search engine
Page 18 / 51
C2-010 / C2-010-I ADSL2+ Router User’s Guide
4-6
3. Under the
Static IP
heading, choose the
Connection Type
from the pull-down menu. This defines both the
connection type and encapsulation method used for your ADSL service. The available options are
Bridged
IP LLC
,
Bridged IP VC-MUX
,
Routed IP LLC
,
Routed IP VC-MUX
or
IPoA
.
.
If have not been provided
specific information for the Connection Type setting, leave the default setting.
4. Change the
IP Address
,
Subnet Mask
,
Gateway Address
and (if available)
Secondary DNS
Server IP
address as instructed by your ISP. These are the global IP settings for the WAN interface. This is the
“visible” IP address of your account. Your ISP should have provided these IP settings to you. For IPoA
(Classic IP over ATM) connections you may need to type in an additional IP address for a
ARP Server
Address
.
If you are using an IPoA connection, ask your ISP if it is necessary to use an ARP (Address
Resolution Protocol) server.
5. Leave the
MTU
value at the default setting (default = 1400) unless you have specific reasons to change
this (see table below).
6. Most users will not need to change
ATM
settings. If this is the first time you are setting up the ADSL
connection it is recommended that you leave the
Service Category
settings at the default values until you
have established the connection. See the table on page
האיגש
!
תרדגומ
הניא
הינמיסה
.
for a description of the
parameters available for ATM traffic shaping.
7. When you are satisfied that all the WAN settings are configured correctly, click on the
Apply
button.
8. The new settings must be saved and the Router must be restarted for the settings to go into effect. To
Save & Reboot
the Router, click on the
Tools
directory tab and then click the
Save & Reboot
menu
button. In the Save and Reboot menu, click the
Reboot
button under
Force the DSL-300T
to system
restart
. The Router will save the new settings and restart. Upon restarting the Router will automatically
establish the WAN connection.
Additional settings for Static IP Address connections:
Static IP
Address
Parameters
Description
Connection
Type
This specifies the connection type and the encapsulation method used for your Static IP
Address connection. The options available are
Bridged IP LLC
,
Bridged IP VC-MUX
,
Routed
IP LLC
,
Routed IP VC-MUX
or
IPoA
.
IP Address
This is the permanent global IP address for your account. This is the address that is visible
outside your private network. Get this from your ISP.
Subnet
Mask
This is the Subnet mask for the WAN interface. Get this from your ISP.
Gateway
Address
This is the IP address of your ISP’s Gateway router. It provides the connection to the Router
for IP routed traffic that is outside your ISP’s network. That is, this will be the primary
connection from the Router to most of the Internet. Get this IP address from your ISP.
Primary
DNS
Address
This is the IP address of the first choice for Domain Name Service (DNS) used to match the
named URL web address used by most browsers with the actual global IP address used for
a web server. Usually this will be a server owned by the ISP. Get this IP address from your
ISP.
Secondary
DNS
Address
This is the second choice for a DNS server. Get this IP address from your ISP.
Default
Route
Enabled/Disabled
this sets the router as the default route between the PCs on your LAN
and the WAN (Internet). This should normally be enabled.
Downloaded from
www.Manualslib.com
manuals search engine
Page 19 / 51
ADSL2+ Router User’s Guide
4-7
Route
NAT
Enabled/Disabled
this enables or disables NAT (Network Address Translation) on the
router.
This should normally be enabled.
IGMP
Enabled/Disabled
this enables or disables IGMP (Internet Group Management Protocol) on
the router.
This should normally be enabled.
Downloaded from
www.Manualslib.com
manuals search engine
Page 20 / 51
C2-010 / C2-010-I ADSL2+ Router User’s Guide
4.2.3
Dynamic IP Address Connection for WAN
A Dynamic IP Address connection configures the Router to automatically obtain its global IP address from
a DHCP server on the ISP’s network. The service provider assigns a global IP address from a pool of
addresses available to the service provider. Typically the IP address assigned has a long lease time, so it will
likely be the same address each time the Router requests an IP address.
To configure a Dynamic IP Address connection, perform the steps listed below. Some of the settings do not
need to be changed the first time the device is set up, but can be changed later if you choose. See the table
below for a description of all the settings available in this menu.
Figure 4-6 WAN Settings Menu – Dynamic IP Address
1. Under the
ATM Interface
settings at the top of the menu (including
VPI
,
VCI
, and
Virtual Circuit
)
should not be changed unless you have been instructed to change them. However, if you are instructed
to change the
VPI
or
VCI
values, type in the values assigned for your account. Leave the
ATM
Interface
and
Virtual Circuit
setting at the default (
Pcv0
and
Enabled
) values for now. This can be
used later if you are configuring multiple virtual circuits for your ADSL service.
2. Under the
Dynamic IP
heading, choose the
Connection Type
from the pull-down menu. This defines
both the connection type and encapsulation method used for your ADSL service. The available options
are
1483 Bridged IP LLC
and
1483 Bridged IP VC-Mux.
If have not been provided specific information
for the Connection Type setting, leave the default setting.
3. Some ISPs record the unique MAC address of your computer’s Ethernet adapter when you first access
their network. This can prevent the Router (which has a different MAC address) from being allowed
access to the ISPs network (and the Internet). To clone the MAC address of your computer’s Ethernet
adapter, type in the MAC address in the
Cloned MAC Address
field and click the
Clone MAC
Address
button.
4. Leave the
MTU
value at the default setting (default = 1400) unless you have specific reasons to
change this (see table below).
4-8
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top