Page 26 / 351 Scroll up to view Page 21 - 25
26
Important Safety Instructions
POWER SUPPLY INSTALLATION
Connect the power supply cord to the power jack on the Motorola Netopia® Gateway. Plug
the power supply into an appropriate electrical outlet.
CAUTION:
Depending on the power supply provided with the product, either the direct
plug-in power supply blades, power supply cord plug or the appliance coupler
serves as the mains power disconnect. It is important that the direct plug-in
power supply, socket-outlet or appliance coupler be located so it is readily
accessible.
CAUTION (North America Only)
: For use only with a CSA Certified or UL
Listed Limited Power Source or Class 2 power supply, rated 12Vdc.
(Sweden)
Apparaten skall anslutas till jordat uttag när den ansluts till ett
nätverk
(Norway)
Apparatet må kun tilkoples jordet stikkontakt.
USB-powered models:
For Use with Listed I.T.E. Only
TELECOMMUNICATION INSTALLATION
When using your telephone equipment, basic safety precautions should always be followed
to reduce the risk of fire, electric shock and injury to persons, including the following:
Do not use this product near water, for example, near a bathtub, wash bowl, kitchen
sink or laundry tub, in a wet basement or near a swimming pool.
Avoid using a telephone (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS
Page 27 / 351
27
Set up the Motorola Netopia® Gateway
Set up the Motorola Netopia® Gateway
Refer to your
Quickstart Guide
for instructions on how to connect your Motorola Netopia®
Gateway to your power source, PC or local area network, and your Internet access point,
whether it is a dedicated DSL outlet or a DSL or cable modem. Different Motorola Neto-
pia® Gateway models are supplied for any of these connections. Be sure to enable
Dynamic Addressing on your PC. Perform the following:
Page 28 / 351
28
Microsoft Windows:
Step 1. Navigate to the TCP/IP Properties Control Panel.
a. Windows 98, ME. and 2000 versions follow a path like this:
Start
menu ->
Settings
->
Control Panel
->
Net-
work
(or
Network and Dial-up Connections
->
Local Area Connection
->
Properties
) ->
TCP/IP
[your_network_card]
or
Internet Protocol [TCP/
IP]
->
Properties
b. Windows XP follows a path like this:
Start
menu ->
Control Panel
->
Network and
Internet Connections
->
Network Connec-
tions
->
Local Area Connection
->
Properties
->
Internet Protocol [TCP/IP]
->
Properties
Then go to Step 2.
Step 2. Select
Obtain an IP address automati-
cally
.
Step 3. Select
Obtain DNS server address auto-
matically
, if available.
Step 4. Remove any previously configured Gate-
ways, if available.
Step 5. OK the settings. Restart if prompted.
Page 29 / 351
29
Set up the Motorola Netopia® Gateway
c. Windows Vista is set to obtain an IP address automatically by default. You may not need
to configure it at all.
To check, open the
Networking
Control Panel and select
Internet Protocol Version 4
(TCP/IPv4)
. Click the
Properties
button.
The
Internet Protocol Version 4 (TCP/IPv4) Properties
window should appear as shown.
If not, select the radio buttons shown above, and click the
OK
button.
Page 30 / 351
30
Macintosh MacOS 9 or higher or Mac OS X:
Step 1. Access the TCP/IP or Network control panel.
a. Mac OS 9 follows a path like this:
Apple
Menu ->
Control Panels
->
TCP/IP
Control Panel
b. Mac OS X follows a path like this:
Apple
Menu ->
System Prefer-
ences
->
Network
Then go to Step 2.
Step 2. Select
Built-in Ethernet
Step 3. Select
Configure Using DHCP
Step 4. Close and Save, if prompted.
Proceed to
Confi
gur
e the Motor
ola
Netopia® Gateway
” on page
31
.

Rate

3.5 / 5 based on 2 votes.

Popular Qwest Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top