1. Home
    2. /
  2. Manuals
    3. /
  3. Prolink
    4. /
  4. H5201
    5. /
  5. 9
Page 41 / 59 Scroll up to view Page 36 - 40
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 41 of 59
Function buttons in this page:
Add Route
Add a user-defined destination route.
Update
Update the selected destination route on the
Static Route Table
.
Delete Selected
Delete a selected destination route on the
Static Route Table
.
Show Routes
Click this button to view the modem/router’s routing table. The IP Route Table displays, as
shown in Figure below.
Page 42 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 42 of 59
9.3
SNMP CONFIGURATION
Simple Network Management Protocol (SNMP) is a troubleshooting and management
protocol that uses the UDP protocol on
port 161
to communicate between clients and
servers. The modem/router can be managed locally or remotely by SNMP protocol.
Fields in this page:
Field
Description
System Description
System description of the modem/router.
System Contact
Contact person or contact information for the modem/router.
System Name
An administratively assigned name for the modem/router.
System Location
The physical location of the modem/router.
System Object ID
Vendor-object identifier. The vendor’s authoritative identification of the
network management subsystem contained in the entity.
Trap IP Address
Destination IP address of the SNMP trap.
Community name
(read-only)
Name of the read-only community. This read-only community allows read
operation to all objects in the MIB.
Community name
Name of the write-only community. This write-only community allows write
Page 43 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 43 of 59
(write-only)
operation to the objects defines as read-writable in the MIB.
Function buttons in this page:
Apply Changes
Save SNMP configuration. New configuration will take effect after saving into flash memory
and rebooting the system
(See section “Admin” for details).
9.4
PORT MAPPING
The modem/router provides multiple interface groups and there are up to five supported
groups, including one default group. The LAN and WAN interfaces could be included.
Traffic coming from one interface of a group can only be flowed to the interfaces of the
same group. Thus, the modem/router can isolate traffic from group to group for some
application. By default, all the interfaces (LAN and WAN) belong to the default group, and
the other four groups are all empty. It is possible to assign any interface to any one group.
Page 44 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 44 of 59
Fields in this page:
Field
Description
Enabled/Disabled
Radio buttons to enable/disable the interface group feature. If disabled, all
interfaces belong to the default group.
Interface groups
To manipulate a mapping group:
a.
Select a group from the table.
b.
Select interfaces from the
Available Interface List
and add it
to the
Grouped Interface List
or vice versa, using the arrow
buttons to manipulate the required mapping of the ports.
c.
Click on “
Apply Changes
” button to save the changes.
Function buttons in this page:
Apply Changes
Save configuration to system. New configuration will take effect after saving into flash
memory and rebooting the system
(See section “Admin” for details).
9.5
IP QoS
The modem/router provides a control mechanism that can provide different priority to
different users or data flows. The QoS (Quality of Service) is enforced by the QoS rules in
the QoS table. A QoS rule contains two configuration blocks:
Traffic Classification
and
Action
. The Traffic Classification feature enables you to classify packets on the basis of
various fields in the packet and perhaps the physical ingress port. The Action
feature
enables you to assign priority level for fields in the packet that matches the Traffic
Classification rule. You can configure any or all field as needed in these two QoS blocks for
a single QoS rule.
Page 45 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 45 of 59
Fields settings on the first block:
Field
Description
IP QoS
Enable/disable the IP QoS function.
Source IP
The IP address of the traffic source.
Source Netmask
The source IP netmask. This field is
required
if the source IP has been
entered.
Destination IP
The IP address of the traffic destination.
Destination
Netmask
The destination IP netmask. This field is
required
if the destination IP has
been entered.
Protocol
The selections are TCP, UDP, ICMP or blank for none. This field is
required
if the source port or destination port has been entered.
Source Port
The source port of the selected protocol. You
cannot
configure this field
without entering the protocol first.
Destination Port
The destination port of the selected protocol. You
cannot
configure this field
without entering the protocol first.
Physical Port
The incoming ports. The selections including LAN ports, Wireless, or blank

Rate

4.3 / 5 based on 3 votes.

Popular Prolink Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top