Page 6 / 59 Scroll up to view Page 1 - 5
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 6 of 59
2 System Overview
2.1
GENERAL DESCRIPTION
Hurricane 5200C/H5201 modem/router is a high-speed ADSL2+ Ethernet router that is
specifically designed to connect to the Internet and to directly connect to your local area
network (LAN) via high-speed 10/100 Mbps Ethernet. The ADSL2+ modem is compatible
with the latest ADSL standards, including ADSL2 and ADSL2+, and supports up to 24
Mbps downstream and 1.5 Mbps upstream to deliver true broadband speed and
throughput.
To ensure full compatibility, the DSL device was tested with all major DSLAMs, and
support standard 10/100 Mbps Base-T Ethernet interface Auto MDI/MDIx 10/100 Switch
function, allowing user to link to PC or other Switches/Hubs easily. The DSL device is an
ideal solution for multi-users utilizing build-in channel mode (PPPoE/A, IPoA, IPoE), IP
routing and NAT functionalities to share the ADSL link. The DSL device is also a perfect
solution for residential users, as it supports users with bridge mode in host based PPPoE
Client.
2.2
SPECIFICATIONS
ADSL Standard
z
ITU-T G.992.1(G.dmt)
z
ANSI T1.413 Issue 2
z
G.992.2 (G.lite)
z
G.994.1 (G.hs)
z
Auto-negotiating rate adaptation
z
ADSL2 G.dmt.bis (G.992.3)
z
ADSL2 G.lite.bis (G.992.4)
z
ADSL2+ (G.992.5)
Software Features
z
RFC-1483/2684 LLC/VC-Mux bridged/routed mode
z
RFC-1577 Classical IP over ATM
z
RFC-2516 PPPoE
z
RFC-2364 PPPoA
z
ITU-T 1.610 F4/F5 OAM send and receive loop-back
z
802.1d Spanning-Tree Protocol
Page 7 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 7 of 59
z
DHCP Client/Server/Relay
z
NAT
z
RIP v1/v2
z
DNS Relay Agent
z
DMZ support
z
IGMP Proxy/Snooping
z
Stateful Packet Inspection
z
Protection against Denial of Service attacks
z
IP Packet Filtering
z
QoS
z
Dynamic DNS
z
UPnP support
z
VoIP/VPN Pass-through
Management
z
Web-based Configuration
z
Menu-driven Command-line Interpreter
z
Telnet Remote Management
z
SNMP v1/v2/Trap
z
Firmware upgrade through FTP, TFTP and HTTP
z
Configuration backup/restore
z
TR069 supported
z
Diagnostic Tool
Page 8 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 8 of 59
3 Hardware Installation
3.1 HARDWARE REQUIREMENTS
z
12V
power adapter
z
RJ-45 Ethernet (LAN/network) cable
z
RJ-11 ADSL (phone) line
z
DSL Splitter (optional )
3.2 HARDWARE SETUP PROCEDURES
1.
Connect the phone line (RJ-11) from Hurricane 5200C/5201 to the wall phone socket.
2.
Connect the network cable (RJ-45) from your PC LAN port (network card) to Hurricane
5200C/5201 Ethernet (LAN) port.
3.
Connect the 12V power adapter.
Page 9 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 9 of 59
4 Software Configuration
When you switch ON the modem/router, the system will boot up and connect to ADSL
automatically. The system provides PVC for bridge test by default. These default
configurations for the system are listed as below.
z
LAN IP address:
192.168.1.1
; Net Mask:
255.255.255.0
z
UART setting: 115200bps, 8 bits, no parity, 1 stop bit, no flow control.
z
VPI/VCI for ATM:
0/35
z
ADSL Line mode: Auto-detect.
You can change the settings via WEB browser. The following sections will describe the
set-up procedures.
Please configure your PC’s LAN port as followed:
z
IP address:
192.168.1.xxx
(e.g. 192.168.1.10)
z
Net Mask:
255.255.255.0
Then, access the Web Console using the steps below:
z
Start your web browser.
z
Type the LAN IP address of the modem/router on the address bar of the browser. The
default IP address is 192.168.1.1.
Page 10 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 10 of 59
Once you are connected to the ADSL2+ router, you will see the status page.
This page displays the ADSL modem/router’s current status and settings. This information
is read-only except for the PPPoE/PPPoA channel for which user can connect/disconnect
the channel on demand. Click on the “Refresh” button to update the status.
Function buttons in this page:
Connect
/
Disconnect
The two buttons take effect only when PVC is configured as PPPoE/PPPoA mode. Click
Connect/Disconnect button to connect/disconnect the PPP dial up link.

Rate

4.3 / 5 based on 3 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top