1. Home
    2. /
  2. Manuals
    3. /
  3. Pirelli
    4. /
  4. PRGAV4202N
    5. /
  5. 9
Page 41 / 182 Scroll up to view Page 36 - 40
PRG AV4202N
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
34
OGU 930500275-A1
Installation Wizard Section
FIGURE 4.
Wireless Setup Panel
VOIP SETUP
This page enables you to configure a VoIP account.
INSTALLATION
COMPLETED
This screen provides a summary of all the above Internet connection configura-
tion steps and their results. Click
Finish
to complete the wizard procedure.
Page 42 / 182
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
Quick Setup Section
OGU 930500275-A1
35
Quick Setup Section
Quick Setup
Section
This chapter will describe the
Quick Setup Section
accessible from the
Home
Page
of the
PRG AV4202N
upon user authentication to the Router.
Be aware that any configuration changes could compromise your connectivity.
When subscribing to a broadband service, you should be aware of the method
by which you are connected to the Internet. Your physical WAN device can be
either Ethernet, DSL, or both. Technical information regarding the properties of
your Internet connection should be provided by your Internet Service Provider
(ISP). For example, your ISP should inform you whether you are connected to
the Internet using a static or dynamic IP address, or what protocols, such as
PPTP or PPPoE, you will be using to communicate over the Internet.
The Router will automatically recognize if you have more than one physical
WAN device on your gateway, and will provide a configuration section for each,
under the 'Internet Connections' section of the 'Quick Setup' screen.
Your WAN connection(s) can be configured using one of the following methods.
Read the configuration instructions relevant to you, by selecting your connection
method from the list below:
1.
Point-to-point protocol over Ethernet (PPPoE) over ATM
2.
Point-to-point protocol over Ethernet (PPPoE) over PTM
3.
Point-to-point protocol over ATM (PPPoA)
4.
Routed Ethernet Connection over ATM (ETHoA)
5.
Bridged Ethernet Connection over ATM (ETHoA)
Page 43 / 182
PRG AV4202N
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
36
OGU 930500275-A1
Quick Setup Section
6.
No Internet connection
FIGURE 1.
Quick Setup Panel
POINT-TO-POINT
PROTOCOL OVER
ETHERNET (PPPOE) OVER
ATM
To configure the Point-to-point protocol over Ethernet, follow these steps:
7.
Select 'Point-to-point protocol over Ethernet (PPPoE)' from the 'Connection
Type' combo-box.
8.
Your Internet Service Provider (ISP) should provide you with the Login user
name and Login password.
9.
If your board features a DSL connection, you will see an 'Automatic PVC
Scan' check box. Select this check box to enable the automatic configuration
of the VPI, VCI and encapsulation parameters (relevant to DSL connec-
tions).
ETHERNET (PPPOE) OVER
PTM
To configure the Point-to-point protocol over Ethernet, follow these steps:
Page 44 / 182
PRG AV4202N
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
Quick Setup Section
OGU 930500275-A1
37
1.
Select 'Point-to-point protocol over Ethernet (PPPoE)' from the 'Connection
Type' combo-box.
2.
Your Internet Service Provider (ISP) should provide you with the Login user
name and Login password.
POINT-TO-POINT
PROTOCOL OVER ATM
(PPPOA)
To configure the Point-to-point protocol over ATM, follow these steps:
1.
Select 'Point-to-point protocol over ATM (PPPoA)' from the 'Connection
Type' combo-box
2.
Your Internet Service Provider (ISP) should provide you with the following in-
formation:
- Login user name
- Login password
3.
By default, the 'Automatic PVC Scan' check box is enabled, which means
that the Router configures the VPI, VCI and encapsulation parameters
automatically. If you would like to configure these parameters manually, un-
check this check box.
- Specify the VPI and VCI values.
- Select the encapsulation method from the combo-box. You can choose
among the following methods: LLC, VCMux and VCMux - HDLC
ROUTED ETHERNET
CONNECTION OVER ATM
(ETHOA)
To configure the Routed Ethernet connection over ATM, follow these steps:
4.
Select 'Routed Ethernet Connection over ATM (ETHoA)' from the 'Connec-
tion Type' combo-box
5.
Your Internet Service Provider (ISP) should provide you with the following in-
formation:
- Specify the value of the VPI and VCI parameters.
- Select the encapsulation method from the combo-box. You can choose
among the following methods: LLC, VCMux.
- Select the Internet Protocol: Most Internet Service Providers (ISPs) provide
dynamic IP addresses, hence the default "Obtain an IP Address Automati-
cally". Should this not be the case, select the "Use the Following IP Address"
option. The screen will refresh. Enter the IP Address, Subnet Mask, Default
Gateway, and DNS Server details provided to you by your ISP.
ROUTED ETHERNET
CONNECTION OVER PTM
(ETHOP)
To configure the Routed Ethernet connection over PTM, follow these steps:
1.
Select 'Routed Ethernet Connection over PTM (ETHoP)' from the 'Connec-
tion Type' combo-box
Page 45 / 182
PRG AV4202N
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
38
OGU 930500275-A1
Quick Setup Section
2.
Your Internet Service Provider (ISP) should provide you with the following in-
formation:
- Select the Internet Protocol: Most Internet Service Providers (ISPs) provide
dynamic IP addresses, hence the default "Obtain an IP Address Automati-
cally". Should this not be the case, select the "Use the Following IP Address"
option. The screen will refresh. Enter the IP Address, Subnet Mask, Default
Gateway, and DNS Server details provided to you by your ISP.
BRIDGED ETHERNET
CONNECTION OVER ATM
(ETHOA)
To configure the Bridged Ethernet Connection over ATM (ETHoA), follow these
steps:
1.
Select 'Bridged Ethernet Connection over ATM (ETHoA)' from the 'Connec-
tion Type' combo-box
2.
Your Internet Service Provider (ISP) should provide you with the following in-
formation:
- Specify the value of the VPI and VCI parameters.
- Select the encapsulation method from the combo-box. You can choose
among the following methods: LLC, VCMux
BRIDGED ETHERNET
CONNECTION OVER PTM
(ETHOP)
To configure the Bridged Ethernet Connection over ATM (ETHoA), follow these
steps:
1.
Select 'Bridged Ethernet Connection over ATM (ETHoA)' from the 'Connec-
tion Type' combo-box
NO INTERNET
CONNECTION
Select 'No Internet Connection' from the 'Connection Type' combo-box. Choose
this connection type if you do not have an Internet connection, or if you want to
disable all existing connections.
WIRELESS
Click the 'Enabled' check box to enable your wireless connection. Specify the
wireless network's ID in the 'SSID' field. The default SSID is 'openrg'.
ADMINISTRATOR
In this section it is necessary to specify the administrator's e-mail in the 'E-mail'
field. System alerts and notifications are sent to this address.

Rate

4.5 / 5 based on 2 votes.

Popular Pirelli Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top