Page 46 / 182 Scroll up to view Page 41 - 45
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
Network Connections Section
OGU 930500275-A1
39
Network Connections Section
Network
Connections
Section
This chapter will describe the
Network Connections Section
accessible from
the
Home Page
of the
PRG AV4202N
.
Be aware that any configuration changes could compromise your connectivity.
This section (see Figure 1) is intended to present a summary of the Router's
connections, such as WAN and LAN (i.e. Ethernet, USB, Wireless) interfaces.
PRG AV4202N
supports various network connections, both physical and logi-
cal. The Network Connections screen enables you to configure the various pa-
rameters of your physical connections, the LAN and WAN, and create new con-
nections, using tunneling protocols over existing connections, such as PPP and
VPN.
Press the
'Advanced'
button to expand the screen and display all connection
entries.
Page 47 / 182
PRG AV4202N
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
40
OGU 930500275-A1
Network Connections Section
FIGURE 1.
Network Connections Panel
LAN BRIDGE
The LAN bridge connection is used to combine several LAN devices under one
virtual network. For example, creating one network for LAN Ethernet and LAN
wireless devices.
Please note, that when a bridge is removed, its formerly underlying devices in-
herit the bridge's DHCP settings. For example, the removal of a bridge that is
configured as DHCP client, automatically configures the LAN devices formerly
constituting the bridge as DHCP clients, with the exact DHCP client configura-
tion.
LAN BRIDGE >> GENERAL
To view and edit the LAN bridge connection settings, click the 'LAN Bridge' link
in the 'Network Connections' screen. The 'LAN Bridge Properties' screen will
appear, displaying a detailed summary of the connection's parameters, under
the 'General' tab. These parameters can be edited in the rest of the screen's
tabs, as described in the following sections.
Page 48 / 182
PRG AV4202N
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
Network Connections Section
OGU 930500275-A1
41
FIGURE 2.
LAN Bridge >> General Panel
LAN BRIDGE >> SETTINGS
General.
This section displays the connection's general parameters. It is re-
commended not to change the default values unless familiar with the network-
ing concepts they represent. Since your gateway is configured to operate with
the default values, no parameter modification is necessary.
Page 49 / 182
PRG AV4202N
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
42
OGU 930500275-A1
Network Connections Section
FIGURE 3.
LAN Bridge >> Settings Panel
Schedule.
By default, the connection will always be active. However, you can
configure scheduler rules in order to define time segments during which the
connection may be active. Once a scheduler rule(s) is defined, this field
changes to a combo-box, allowing you to choose between the available rules.
Network.
Select whether the parameters you are configuring relate to a WAN,
LAN or DMZ connection, by selecting the connection type from the combo-box.
Physical Address.
The physical address of the network card used for your
network. Some cards allow you to change this address.
MTU.
MTU is the Maximum Transmission Unit. It specifies the largest packet
size permitted for Internet transmission. In the default setting, Automatic, the
Page 50 / 182
PRG AV4202N
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
Network Connections Section
OGU 930500275-A1
43
gateway selects the best MTU for your Internet connection. Select "Automatic
by DHCP" to have the DHCP determine the MTU. In case you select "Manual",
it is recommended to enter a value in the 1200 to 1500 range.
Internet Protocol.
Select one of the following Internet protocol options from the
'Internet Protocol' combo-box:
-
No IP Address
: Select 'No IP Address' if you require that your gateway have
no IP address. This can be useful if you are working in an environment where
you are not connected to other networks, such as the Internet.
-
Obtain an IP Address Automatically
: Your connection is configured by default
to act as a DHCP client. You should keep this configuration in case your service
provider supports DHCP, or if you are connecting using a dynamic IP address.
The server that assigns the gateway with an IP address, also assigns a subnet
mask. You can override the dynamically assigned subnet mask by selecting the
'Override Subnet Mask' and specifying your own mask instead. You can press
the 'Release' button to release the current leased IP address. Once the address
has been released, the button text changes to 'Renew'. Use the 'Renew' button
to renew the leased IP address.
-
Use the Following IP Address
: Your connection can be configured using a
permanent (static) IP address. Your service provider should provide you with
such an IP address and subnet mask.
DNS Server.
Domain Name System (DNS) Server is the method by which Web
site domain names are translated into IP addresses. You can configure the
connection to automatically obtain a DNS server address, or specify such an
address manually, according to the information provided by your ISP. If you
have previously chosen “Obtain an IP Address Automatically”, a combo-box will
appear.
To configure the connection to automatically obtain a DNS server address, se-
lect 'Obtain DNS Server Address Automatically' from the 'DNS Server' drop
down menu.
To manually configure DNS server addresses, select 'Use the Following DNS
Server Addresses' from the 'DNS Server' drop down menu. Specify up to two
different DNS server address, one primary, another secondary.
IP Address Distribution.
The 'IP Address Distribution' section allows you to
configure the gateway's Dynamic Host Configuration Protocol (DHCP) server
parameters. The DHCP automatically assigns IP addresses to network PCs. If
you enable this feature, make sure that you also configure your network PCs as
DHCP clients. Select one of the following options from the 'IP Address Distribu-
tion' combo-box:
DHCP Server.
Start IP Address
: The first IP address that may be assigned to a LAN host.
Since the gateway's default IP address is 192.168.1.1, this address must be
192.168.1.2 or greater.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top