Page 11 / 35
Scroll up to view Page 6 - 10
DISCUS™ DRG A225G
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
13
HARDWARE INSTALLATION
Positioning the
router
You should place the Router in such a location to ensure that:
•
It is located near an electrical outlet and a phone wall socket
•
Water or moisture cannot enter the case of the unit
•
It is out of direct sunlight and away from sources of heat
•
The cabling is away from power lines, fluorescent lighting fixtures, and sources
of electrical noise such as radios, transmitters and broadband amplifiers.
•
It is centrally located with respect to the wireless devices that will be connected
to the Router. A suitable location might be on top of a high shelf to ensure the
maximum coverage for all connected devices.
Downloaded from
www.Manualslib.com
manuals search engine
Page 12 / 35
DISCUS™ DRG A225G
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
14
Connecting the
router
The first step to install the router is to physically connect it to the telephone
socket and then to connect it to a computer by means of an Ethernet or an
USB connection.
To connect the phone cable:
1.
Connect one end of the phone cable into the telephone socket.
2.
Connect the other end of the phone cable into the DSL port on the rear of
the Router
FIGURE 1.
Phone Cable Connection
Downloaded from
www.Manualslib.com
manuals search engine
Page 13 / 35
DISCUS™ DRG A225G
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
15
To connect the Ethernet cable:
1.
Connect one end of the Ethernet cable into one of the four Ethernet ports on
the rear of the Router
2.
Connect the other end of the Ethernet cable into the Ethernet Network card
of your computer
3.
Verify if the Ethernet Network card is configured as DHCP client, otherwise
configure it to remain in the same local network of the router interface.
FIGURE 2.
Ethernet Cable Connection
Downloaded from
www.Manualslib.com
manuals search engine
Page 14 / 35
DISCUS™ DRG A225G
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
16
To connect the USB cable, follow the procedure according to your Operating
System:
WINDOWS
1.
Connect one end of the USB cable into the USB port of your PC
2.
Browse till
x:\USB driver
folder (where “
x
” is the CD-ROM drive unit letter);
launch the “
setup.exe
” executable (“
x:\USB driver\setup.exe
”) and follow
setup instructions
3.
The setup software will invite you to plug the other end of the USB cable into
the USB port on the rear of the Router
MAC 10.x
1.
Connect one end of the USB cable into the USB port of your PC
2.
Connect the other end of the USB cable into the USB port on the rear of the
Router. The Operating System will automatically recognize the device
FIGURE 3.
USB Cable Connection
Don’t plug the other end of the USB cable until setup software will ask you to do it.
Downloaded from
www.Manualslib.com
manuals search engine
Page 15 / 35
DISCUS™ DRG A225G
© (2007) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
17
Connecting the
phones
To connect the phones please refer to the following picture.
You can connect only phone set(s) which comply with the Hungarian regula-
tions.
FIGURE 4.
Phones Connection
Downloaded from
www.Manualslib.com
manuals search engine
19216811.live