1. Home
    2. /
  2. Manuals
    3. /
  3. PCI
    4. /
  4. BLW-54MF
    5. /
  5. 4
Page 16 / 78 Scroll up to view Page 11 - 15
2
11
Chapter 2 Basic Setup & Configuration
3.After entering the system, BLW-54MF will show you the Main page.
During configuration, you can use the tabs on the top of the page and
menu at the left side of the page to navigate. Besides, it is necessary that,
after configuring, you should click
ņ
Apply
Ň
to enable the settings you
have made.
If your BLW-54MF Wireless Router does not response, and you
cannot enter the web configuration page, please follow the steps
below to check if there is any problem:
1.Make sure that BLW-54MF Wireless Router is properly installed
and powered on, and LAN connection is O.K. You can test the
connection by using
ņ
Ping
Ň
command:
Ś
Open MS-DOS window or click
ņ
Start
Ɩ
Run
ĀŇ
on the
desktop to show the command prompt window.
Ś
Enter the command:
Ś
If it shows the message of
ņ
Request time out,
Ň
the problem
can be either disorder of connection, or the conflict between
your PC's IP address and the router
Ņ
s IP address.
2.If your PC uses static IP address, the IP address must between
in the range of 192.168.1.2~192.168.1.254, in order not to
occupy the BLW-54MF
Ņ
s default IP address
ņ
192.168.1.1.
Ň
In addition, the subnet mask must be
ņ
255.255.255.0.
Ň
To
know more details of your PC and Internet connection, please
check the TCP/IP settings on your PC.
Page 17 / 78
2
12
BLW-54MF
3.You have to make sure that your PC and BLW-54MF are on the
same segment. Besides, you have to use the wired LAN interface
when first accessing the web configuration page, the wireless
interface only works when the settings of BLW-54MF matches
your PC's wireless settings.
4. Setup Wizard
After logging in the configuration page, a
ņ
Setup Wizard
Ň
dialog box
pops up. You may choose to use setup wizard to set up BLW-54MF or use
configuration page to set up all the settings. You may use wizard to help
you complete setting up and start connect with Internet through simply a
few steps. Please follow the instructions below to do the configuration.
If you do
NOT
want to see setup wizard popping up whenever
you open the main page, please click
ņ
No
Ň
after the words
ņ
display wizard next time?
Ň
on the setup wizard window. And
when next time you enter the main page of BLW-54MF, it will not
activate setup wizard.
Page 18 / 78
2
13
Chapter 2 Basic Setup & Configuration
4.1 Set Password
Step 1
Ĉ
The default User Name of BLW-54MF Wireless Router is
ņ
admin
Ň
and Password is
ņ
admin.
Ň
It is recommended that you should
change the default password to have better protection over the router and
the LAN. You must memorize the password set by you to enter the system;
otherwise, you have to restore the whole systems and then configure the
settings again. Please enter your new password twice on the following page
and then click
ņ
Next
Ň
to keep on setting up.
4.2 Choose Time Zone
Step 2
Ĉ
You can set the system time according to the time zone where you
locate now. You may scroll down the list to find a suitable time zone.
Page 19 / 78
2
14
BLW-54MF
4.3 Set LAN & DHCP Server
Step 3
Ĉ
You can do LAN port configuration and enable/disable DHCP
server through this page.
œ
LAN IP Address
Ĉ
Here is the IP address of the LAN side of BLW-
54MF. The default IP address is
ņ
192.168.1.1
Ň
.
œ
LAN Subnet Mask
Ĉ
The Subnet Mask of the LAN side of BLW-54MF
is
ņ
255.255.255.0
Ň
.
œ
DHCP Server
Ĉ
DHCP stands for
Dynamic Host Control Protocol.
BLW-54MF Wireless Broadband Router has a built-in DHCP server
which can automatically assign an IP address to those computers on the
LAN/private network. Click to enable/disable DHCP server.
œ
Range Start
Ĉ
The first IP address which DHCP server of BLW-54MF
starts to distribute.
œ
Range End
Ĉ
The last IP address which DHCP server of BLW-54MF
distributes.
œ
Next
Ĉ
Click this button to save the settings and go to next page.
Page 20 / 78
2
15
Chapter 2 Basic Setup & Configuration
4.4 Select Internet Connection Type
Step 4
Ĉ
The followings are the most common used connection types:
Obtain IP automatically (DHCP client), Fixed IP address, and PPPoE. If
you want to know more about the other types of WAN configurations,
please refer to
ņ
Main
Ň
configuration page.
After auto-detecting WAN, the setup wizard might skip the page of
ņ
Select Internet Connection Type
Ň
page and directly shows the
detected connection type. If BLW-54MF shows the connection mode
which you do not want to use, click
ņ
Back
Ň
to the previous page to select
the Internet connection type.
Ɩ
Obtian IP automatically (DHCP client)
1.If you use cable modem, or you are a DHCP client, you may choose this
entry and use the wizard to configure.

Rate

3.5 / 5 based on 2 votes.

Popular PCI Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top