Page 61 / 181 Scroll up to view Page 56 - 60
iConnect625W ADSL/ADSL2+ Router User Guide
61
7.2.8
Delete an Existing Connection
Follow the steps below to delete a WAN connection.
Step 1
:
To begin, click the
Setup tab
on the top menu, and click the connection you
wish to delete from the left hand menu.
Step 2
:
Click the
Delete
button on the applicable connection you wish to remove.
The changes take effect when you click Delete. However, if the iConnect625W
router configuration is not saved, these changes will be lost when you reboot the
iConnect625W router.
Step 3
:
To save your configuration, please refer to the section under
Save / Restart
Menu
.
Page 62 / 181
iConnect625W ADSL/ADSL2+ Router User Guide
62
7.2.9
Modem Setup
To configure the ADSL modulation types, follow the steps below.
Step 1
:
To begin, click the
Setup tab
on the top menu. Click the
Modem
link. The
following page appears:
Step 2:
The
Modulation Type
checkboxes are defaulted to the above settings as
shown. It is recommended that the default settings remain.
The iConnect625W router is pre-configured to detect the ADSL modulation type
automatically. In most cases, this screen should not be modified.
Step 3
:
If any modulation type has been amended, click the
Apply
button.
Step 4
:
To save your configuration, please refer to the section under
Save / Restart
Menu
.
Page 63 / 181
iConnect625W ADSL/ADSL2+ Router User Guide
63
The following table lists the
Modem
screen fields and their definitions:
Field
Description
There are multiple combinations of ADSL modulation modes to be selected.
No Mode
No mode is defaulted to disabled.
ADSL_G.dmt
G.dmt stands for G Discrete Multi-Tone. It supports ITU-U
ADSL over POTS (G.992.1).
ADSL_G.lite
It support ITU-T ADSL over POTS (G.992.2)
ADSL_G.dmt.bis
It supports ITU-T ADSL 2 over POTS (G.992.3)
ADSL_G.dmt.bis.DELT
It supports ADSL G.DMT.bis DELT
ADSL_2plus
It supports ITU-T ADSL 2+ over POTS (G.992.5) and
speeds up to 24Mbps.
ADSL_2plus_DELT
It supports ADSL 2+ and speeds up to 24Mbps.
ADSL re-adsl
It supports ITU-T RE-ADSL 2 over POTS (G.992.3).
ADSL re-adsl DELT
It supports ADSL re-adsl DELT.
ADSL_ANSI_T1.413
This applies to ANSI T1.413-1998.
MULTI_MODE
Multi-Mode
is automatically detected.
ADSL_G.dmt.bis_AnxM
It supports ITU-T ADSL 2 G.992.3 Annex M.
ADSL2plus_AnxM
It supports ITU-T ADSL 2+ G.992.5 Annex M.
Page 64 / 181
iConnect625W ADSL/ADSL2+ Router User Guide
64
8.
Advanced
The iConnect625W supports a host of advanced networking and routing features including
the setup of your LAN and WAN interfaces, security, port configuration, user management,
restarting the router and plug and play capability.
In addition, it allows you to performance advanced configuration functions for existing
connection such as enabling and disabling voice, voice provision, UPnP, SNTP, SNMP
and so on.
There should be at least one WAN connection configured before implementing advanced
WAN configuration features. Similarly, at least one LAN group must be defined before
advanced LAN configuration features can be implemented.
The features include:
±
Universal Plug and Play (UPnP)
±
Simple Networking Timing Protocol (SNTP)
±
Simple Network Management Protocol (SNMP)
±
Port Forwarding
±
IP Filters
±
LAN Clients
±
LAN Isolation between LAN groups
±
Remote Web Access
±
Bridge Filters
±
Dynamic DNS Client
±
Internet Group Management Protocol (IGMP) Proxy
±
Static Routing
±
Dynamic Routing
±
Policy Database
±
Ingress
±
Egress
±
Shaper
±
SSH Access Control
To access the
Advanced
configuration screen, follow the steps below.
Step 1:
Click the
Advanced
tab to access the advanced configuration features. The
following page appears:
Page 65 / 181
iConnect625W ADSL/ADSL2+ Router User Guide
65
Step 2:
Please refer to the sections below on how to configure the advanced features.

Rate

4.5 / 5 based on 2 votes.

Popular Open-Networks Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top