Open-Networks iConnect625W Router Manual PDF (Setup & Configuration Guide)

Page 56 / 181 Scroll up to view Page 51 - 55

iConnect625W ADSL/ADSL2+ Router User Guide

56

The following table lists the

Bridge Connection Setup

screen and their definitions:

Field

Description

Each of the fields for

Bridge Settings

is described as follows.

LLC and

VC

are two different methods of

encapsulating multiple sessions. The default is set to

LLC

.

LLC

With

LLC

encapsulation, a link control

header is added to the Ethernet packet that

identifies the protocol type (Ethernet). This

allows multiple protocols to be transmitted

over the ATM Virtual Circuit (VC).

Encapsulation

VC

With

VC m

ultiplexing, .no link control header

is needed as the ATM VC is assumed to be

carrying a single protocol.

Bridge

Settings

Select LAN

Select the LAN Group (as defined in the

LAN

Configuration

screen) for the bridged connection. The

options are:

•

LAN Group 1

•

LAN Group 2

•

LAN Group 3

•

LAN Group 4

•

LAN Group 5

•

None

The

Bridge

connection is added to the LAN Group

configuration, unless you have selected the option:

None.

In this case, the connection will be added to

the

Interfaces

box instead.

Apply

Applies the changes made to the connection.

Delete

Deletes the connection.

Cancel

Cancels the changes made to the connection.

For VLAN and PVC field descriptions, please refer to the table under PPPoE section.

Page 57 / 181

iConnect625W ADSL/ADSL2+ Router User Guide

57

7.2.6

CLIP Connection Setup

Classical IP Over ATM as defined in RFC1577 provides the ability to transmit IP packets

over an ATM network. CLIP support encapsulates IP in an AAL5 Packet Data Unit (PDU)

frame using RFC 1577 and it sends out an ARP request to a CLIP-enable ARP server,

which returns the ATM address.

To configure

CLIP

connection, follow the steps provided below.

Step 1

:

To begin, click the

Setup tab

on the top menu. Click the

New Connection

link.

The following page appears if no prior connection has been configured:

Step 2

:

From the

Type

drop-down list, select

CLIP.

The following page appears:

Page 58 / 181

iConnect625W ADSL/ADSL2+ Router User Guide

58

Step 3

:

Enter a unique name for your

Bridged

connection in the

Name

field. The name

must not have spaces and cannot begin with numbers.

Step 4:

The

NAT

and

Firewall

checkboxes are checked by default under the

Options

field. Leave these in the default mode.

Step 5:

In the

IP Address

field, enter your assigned IP address based on the

information provided by your ISP.

Step 6:

In the

Mask

field, enter the Subnet Mask based on the information provided by

your ISP.

Step 7:

In the

ARP Server

field, enter the

ARP Server

address based on the

information provided by your ISP.

Step 8:

In the

Default Gateway

field, the

Default Gateway

is blank

.

Enter this field

based on the information provided by your ISP.

Step 9:

In the

PVC Settings

section, the

VPI

and

VCI

values are defaulted to

8

and

35

,

respectively. Make the changes in these fields, as provided by your ISP, if

required.

If you need to use the VPI and VCI values in an existing connection, you will need to open

it and edit the settings. It is not possible to have more than one connection using the

same VPI/VCI values.

Step 10:

Select the

QoS

. Leave the default value if you are unsure or if the ISP did not

provide this information.

The

PCR, SCR, MBS

and

CDVT

fields could be enabled/disabled depending

on the

QoS

section. Your ISP should provide these values.

Step 11

: Click the

Apply

button.

Step 12:

To save your configuration, please refer to the section under

Save / Restart

Menu

.

Page 59 / 181

iConnect625W ADSL/ADSL2+ Router User Guide

59

The following table lists the

CLIP Connection Setup

screen and their definitions:

Field

Description

NAT

Network Address Translation is a feature that enables you to use

private IP addresses on your computer or your LAN.

This is set to

Enabled

by default for standard operation.

Firewall

Select to enable security for this connection.

This is set to

Enabled

by

default for standard operation.

Each of the fields for

CLIP Settings

is described as follows.

LLC and

VC

are two different methods of

encapsulating multiple sessions. The default is set to

LLC

.

LLC

With

LLC

encapsulation, a link control

header is added to the Ethernet packet that

identifies the protocol type (Ethernet). This

allows multiple protocols to be transmitted

over the ATM Virtual Circuit (VC).

Encapsulation

VC

With

VC m

ultiplexing, .no link control header

is needed as the ATM VC is assumed to be

carrying a single protocol.

IP Address

The CLIP Server IP Address provided by

your ISP.

Mask

The CLIP Server Subnet Mask provided by

your ISP.

ARP Server

The Address Resolution Protocol (ARP)

Server IP Address provided by your ISP.

CLIP

Settings

Default Gateway

If checked, this WAN connection acts as the

default gateway to the Internet.

Apply

Applies the changes made to the connection.

Delete

Deletes the connection.

Cancel

Cancels the changes made to the connection.

For VLAN and PVC field descriptions, please refer to the table under PPPoE section.

Page 60 / 181

iConnect625W ADSL/ADSL2+ Router User Guide

60

7.2.7

Modify an Existing Connection

Follow the steps below to modify an existing connection.

Step 1

:

To begin, click the

Setup tab

on the top menu, and click the connection you

wish to modify from the left hand menu.

Step 2

:

Edit as applicable on the individual connection page.

Step 3

:

Click the

Apply

button.

Step 4:

To save your configuration, please refer to the section under

Save / Restart

Menu

.

Rate

Popular Open-Networks Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share