Page 16 / 101 Scroll up to view Page 11 - 15
11
Accessing the Network
4G LTE
With LTE bandwidth (700 MHz) you can get the broadband-like speed you require to work efficiently
outside the home or office. You can connect to the Internet, access your corporate intranet, check
your email and download attachments at speeds that are up to 10 times faster than 3G*.
4G Mobile Broadband with LTE*
Download: typical download speeds of 5-12 Mbps
Upload: typical upload speeds of 2-5 Mbps
3G Mobile Broadband with EVDO Rev. A**
Download: typical download speeds of 600 kbps–1.4 Mbps with bursts up to 3.1 Mbps.
Upload: typical upload speeds of 500-800 kbps with bursts up to 1.8 Mbps.
GSM Mobile Broadband with HSPA+, WCDMA, EDGE and GPRS***
Download and upload speeds depend on the roaming network.
WiFi 802.11b/g/n
802.11b uses the 2.4 GHz frequency with a bandwidth of 11 Mbps.
802.11g uses the 2.4 GHz frequency with a bandwidth of 54 Mbps.
802.11n uses the 2.4 GHz frequency with a bandwidth of 150 Mbps.
*
Speeds shown are those published by Verizon Wireless, Inc. and are theoretical in nature. Actual throughput speed and coverage
may vary. Speed claims not applicable when roaming.
**
Mobile Broadband Rev.A speed claim based on Verizon Wireless network tests with 5 MB FTP data files without compression.
Your Mobile Broadband Rev. A-enabled device will indicate coverage when you are in a Mobile Broadband Rev. A service area.
When outside the Rev. A service area, your wireless device will revert to Mobile Broadband Rev. 0 (typical download speeds will
be 400–700 Kbps and upload speeds will be 60–80 Kbps).
***
Subject to Customer Agreement, Calling Plan, credit approval, and other service terms.
Page 17 / 101
12
Using the Device for the First Time
To get started, follow these steps:
Confirm your computer meets the minimum system requirements. (See
System
Requirements
on page 3.)
Assemble the wall charger. (See
Assemble the Wall Charger
on page 13.)
Install the 4G LTE SIM card. (See
Install the 4G LTE SIM Card
on page 13.)
Insert and charge the battery. (See
Insert and Charge the Battery
on page 15.)
Turn on the device. (See
Power the MiFi 4620L On and Off
on page 18.)
Connect the device to your computer using Wi-Fi. (See
Connecting to the Device
on
page 19.)
Connect to MiFi Settings. (See
Connect to MiFi Settings
on page 19.)
Page 18 / 101
13
Assemble the Wall Charger
The wall charger comes with a removable plug. You need to connect it before using the MiFi device
for the first time. To assemble the wall charger, follow these steps:
Remove the plug and the wall charger from the package.
Slide the plug on to the wall charger.
Install the 4G LTE SIM Card
To install your new 4G LTE SIM card, follow these steps:
Open the cover located on the underside of the MiFi 4620L.
Remove SIM card from the outer card, being careful not to touch the gold-colored contacts.
Hold the card as shown with the gold-colored contact points facing down.
Insert the SIM card into the slot. The 4G SIM card MUST remain in the SIM card slot when
in use.
Your SIM (Subscriber Identity Module) card is a small rectangular plastic card that stores your phone
number and important information about your wireless service.
CAUTION!
Do not bend or scratch your SIM card. Avoid exposing your SIM card to static
electricity, water, or dirt.
Page 19 / 101
14
Remove the 4G LTE SIM Card
To remove the 4G LTE SIM card, follow these steps:
Open the SIM card cover located on the underside of the MiFi 4620L. Press down firmly on
the small black tab to the left side of the SIM card slot.
Apply firm pressure to the right side of the SIM card and push to slide the card over the small
black tab. A piece of transparent tape can be attached to the end of the SIM card once it has
been pushed over the small black tab to complete lifting the card out of the slot.
NOTE
Should your 4G SIM card be lost or damaged, contact your network operator.
Page 20 / 101
15
Insert and Charge the Battery
IMPORTANT
Before you use your device, be sure to charge the battery for at least three hours
to ensure a full initial charge.
To insert and charge the battery, follow these steps:
Insert your fingernail into the indention on the back cover and lift to open the battery
compartment, located on the bottom of the device. Set the cover aside.
Align the gold-colored contacts on the battery with the gold-colored contacts on the device
and gently slide the battery into place.
Replace the cover by setting it on the device where the notches align, and then press on the
cover until it clicks into place.

Rate

4 / 5 based on 1 vote.

Popular Novatel Wireless Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top